Difference between revisions of "Williams System 8"
| (15 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
{{WIP}} | {{WIP}} | ||
| − | Click to go back to the [ | + | Click to go back to the [[Williams_Repair_Guides | Williams solid state repair guides index]]. |
=Introduction= | =Introduction= | ||
| − | [[File:System_8_Boardset.JPG|200px|thumb|left|Williams System 8 Board Set]] | + | [[File:System_8_Boardset.JPG|200px|thumb|left|Williams System 8 Board Set]] |
The Williams System 8 boardset was used in 1984 with only two games, the pitch and bat Pennant Fever and Still Crazy, a novelty game. Combining the driver board, sound board, and cpu directly onto one board eliminated several design deficiencies of the earlier System 3-7 boardsets; mainly the 40 pin interconnector, and extra wiring harness interboard connectors.<br> | The Williams System 8 boardset was used in 1984 with only two games, the pitch and bat Pennant Fever and Still Crazy, a novelty game. Combining the driver board, sound board, and cpu directly onto one board eliminated several design deficiencies of the earlier System 3-7 boardsets; mainly the 40 pin interconnector, and extra wiring harness interboard connectors.<br> | ||
System 8 is very similar to its successor (System 9), but it is more of a "slimmed down" version. There are a total of 8 controlled solenoids versus the 16 used with the system 9 boardset. Another distinct difference is system 8 hardware does not utilize special solenoids. System 8 also lacks the connector for a speech daughterboard. | System 8 is very similar to its successor (System 9), but it is more of a "slimmed down" version. There are a total of 8 controlled solenoids versus the 16 used with the system 9 boardset. Another distinct difference is system 8 hardware does not utilize special solenoids. System 8 also lacks the connector for a speech daughterboard. | ||
| − | Although | + | Although System 8 is capable of driving four 7-digit displays and one 4 digit display, only two 7-digit displays are used with Pennant Fever and one 7-digit display is used with Still Crazy. Therefore, master display boards are not used on either game. Both the lamp and switch matrices are 8 x 8 in size, but neither Pennant Fever nor Still Crazy use many switches in their matrices. |
<br clear=all> | <br clear=all> | ||
| Line 29: | Line 29: | ||
==CPU Driver Board== | ==CPU Driver Board== | ||
| − | [[File:WMS Sys8 CPU.jpg|200px|thumb|left|System 8 CPU rev A (Pennant Fever)]] | + | [[File:WMS Sys8 CPU.jpg|200px|thumb|left|System 8 CPU rev A (Pennant Fever). Note: The insect on connector J8 is not OEM issued.]] |
[[File:System_8_cpu_x1.jpg|200px|thumb|left|System 8 CPU rev X1 (Still Crazy)]]<br clear=all> | [[File:System_8_cpu_x1.jpg|200px|thumb|left|System 8 CPU rev X1 (Still Crazy)]]<br clear=all> | ||
==Power Supply== | ==Power Supply== | ||
| − | [[File:System_8_Power_Supply.JPG|200px|thumb|left|System 8 Power Supply]]<br clear=all> | + | [[File:System_8_Power_Supply.JPG|200px|thumb|left|System 8 Power Supply]]<br> |
| + | The System 8 power supply is identical to a System 7 and System 9 power supply. | ||
| + | <br clear=all> | ||
=Problems and Solutions= | =Problems and Solutions= | ||
| Line 42: | Line 44: | ||
=== Relocating the battery from the MPU board === | === Relocating the battery from the MPU board === | ||
| + | Use the same procedure as detailed in the System 9 section, [http://www.pinwiki.com/wiki/index.php?title=Williams_System_9_-_11#Relocating_the_battery_from_the_System_9_MPU_board here]. | ||
=== Repairing Alkaline Corrosion === | === Repairing Alkaline Corrosion === | ||
| − | + | Use the same procedure as detailed in the System 11 section, [http://www.pinwiki.com/wiki/index.php?title=Williams_System_9_-_11#Repairing_Alkaline_Corrosion here]. | |
=== Connecting a logic probe to the MPU === | === Connecting a logic probe to the MPU === | ||
| Line 51: | Line 54: | ||
To connect a logic probe, pick up +5V at the top lead of capacitor C6 (a trace extends down from the larger electrolytic cap at C5).<br> | To connect a logic probe, pick up +5V at the top lead of capacitor C6 (a trace extends down from the larger electrolytic cap at C5).<br> | ||
| − | Pick up ground at pin 9 of 1J5. | + | Pick up ground at pin 9 of 1J5.<br> |
| + | |||
| + | Of course, +5v and ground can always be acquired at any one of the bypass capacitors, which are located at most every chip, and simply labeled as "B". | ||
<br clear=all> | <br clear=all> | ||
| Line 57: | Line 62: | ||
[[File:System8PowerOnTheBenchAnnotated.jpg|200px|thumb|left|Powering the System 8 MPU on the bench with an old PC power supply.]]<br> | [[File:System8PowerOnTheBenchAnnotated.jpg|200px|thumb|left|Powering the System 8 MPU on the bench with an old PC power supply.]]<br> | ||
| − | + | For full operation a System 8 MPU requires +5V, +12V, -12V DC and ground. However, -12V is only required for the sound amplifier, so that voltage may be omitted for non-sound-related testing. | |
Connect... | Connect... | ||
| Line 98: | Line 103: | ||
*A remotely located volume pot may be used to adjust volume levels. | *A remotely located volume pot may be used to adjust volume levels. | ||
*The analog audio is then presented to the TDA2002 for final amplification. | *The analog audio is then presented to the TDA2002 for final amplification. | ||
| + | *The amplified audio is presented to the single 8 ohm cabinet speaker. | ||
| + | <br clear=all> | ||
| + | |||
| + | Pennant fever makes only 8 sounds. | ||
| + | #"Charge" bugle theme | ||
| + | #Organ music, "The Lone Ranger" theme | ||
| + | #"You're out!" | ||
| + | #"Boooo!" | ||
| + | #"Strike One" | ||
| + | #"Strike Two" | ||
| + | #"All right!" | ||
| + | |||
| + | Pressing switch 3 on the MPU should cause the sound system to play "FirePower-like" sounds continuously until power to the game is turned off. | ||
Note that the sound subsystem can be configured to use either a 6808 or a 6802 microprocessor.<br>To use a 6808, jumper W1 should be in, W2 out.<br>To use a 6802, jumper W1 should be out, W2 in. | Note that the sound subsystem can be configured to use either a 6808 or a 6802 microprocessor.<br>To use a 6808, jumper W1 should be in, W2 out.<br>To use a 6802, jumper W1 should be out, W2 in. | ||
| + | |||
| + | == Replacing a System 8 MPU with a System 9 MPU == | ||
| + | Yes, it's possible. | ||
| + | |||
| + | [[media:Pennant_Fever_MPU_Conversion.pdf|PDF Instructions]] ([https://docs.google.com/document/d/1wDpqiM6byeekyw09s1HiOXocrVG9AlLY/ Document Source]) | ||
=Repair Logs= | =Repair Logs= | ||
Did you do a repair? Log it here as a possible solution for others. | Did you do a repair? Log it here as a possible solution for others. | ||
Latest revision as of 17:42, 20 May 2023
 |
Click to go back to the Williams solid state repair guides index.
1 Introduction
The Williams System 8 boardset was used in 1984 with only two games, the pitch and bat Pennant Fever and Still Crazy, a novelty game. Combining the driver board, sound board, and cpu directly onto one board eliminated several design deficiencies of the earlier System 3-7 boardsets; mainly the 40 pin interconnector, and extra wiring harness interboard connectors.
System 8 is very similar to its successor (System 9), but it is more of a "slimmed down" version. There are a total of 8 controlled solenoids versus the 16 used with the system 9 boardset. Another distinct difference is system 8 hardware does not utilize special solenoids. System 8 also lacks the connector for a speech daughterboard.
Although System 8 is capable of driving four 7-digit displays and one 4 digit display, only two 7-digit displays are used with Pennant Fever and one 7-digit display is used with Still Crazy. Therefore, master display boards are not used on either game. Both the lamp and switch matrices are 8 x 8 in size, but neither Pennant Fever nor Still Crazy use many switches in their matrices.
2 Games
| Title | Date of Release | Model # | Other Boards | Notes |
|---|---|---|---|---|
| Pennant Fever | 05-1984 | 526 | CPU rev A | Pitch and Bat |
| Still Crazy | 06-1984 | 534 | CPU rev X1 | Novelty Vertical Pinball |
3 Technical Info
3.1 CPU Driver Board
3.2 Power Supply
The System 8 power supply is identical to a System 7 and System 9 power supply.
4 Problems and Solutions
4.1 Power Problems
4.2 MPU boot issues
4.2.1 Relocating the battery from the MPU board
Use the same procedure as detailed in the System 9 section, here.
4.2.2 Repairing Alkaline Corrosion
Use the same procedure as detailed in the System 11 section, here.
4.2.3 Connecting a logic probe to the MPU
The System 8 MPU lacks test points. Argh!
To connect a logic probe, pick up +5V at the top lead of capacitor C6 (a trace extends down from the larger electrolytic cap at C5).
Pick up ground at pin 9 of 1J5.
Of course, +5v and ground can always be acquired at any one of the bypass capacitors, which are located at most every chip, and simply labeled as "B".
4.2.4 Using a PC Power Supply For Bench Testing
For full operation a System 8 MPU requires +5V, +12V, -12V DC and ground. However, -12V is only required for the sound amplifier, so that voltage may be omitted for non-sound-related testing.
Connect...
- Ground to pin 1, 2, or 3
- +5VDC to pin 4, 5,or 6
- -12VDC to pin 8
- +12VDC to pin 9
4.3 Game resets
4.4 Solenoid problems
this is a stub
4.5 Lamp problems
4.5.1 Lamp Matrix Row and Column Testing
4.6 Switch problems
4.6.1 Switch Matrix Row and Column Testing
4.7 Display problems
WARNING: This circuit uses high voltages. Don't continue, unless you are confident in your diagnostic abilities.
4.8 Sound problems
The System 8 MPU creates sound on the MPU itself, much like the baseline version of the System 11 MPU.
General System 8 Sound Subsystem Theory of Operation
- The sound subsystem consists of a 6808/2 processor, 6821 PIA, 1408 DAC, and finally a TDA2002 amplifier.
- Sounds are conveyed to the sound subsystem by the main processor via the input ports of the 6821 PIA at IC13.
- The 6808 at IC11 reads the PIA input port then pulls the appropriate sound file from the sound ROM at IC49.
- The 6808 sends the sound data back to the 6821s second set of output ports, which are attached to the 1408 digital-to-analog converter.
- A remotely located volume pot may be used to adjust volume levels.
- The analog audio is then presented to the TDA2002 for final amplification.
- The amplified audio is presented to the single 8 ohm cabinet speaker.
Pennant fever makes only 8 sounds.
- "Charge" bugle theme
- Organ music, "The Lone Ranger" theme
- "You're out!"
- "Boooo!"
- "Strike One"
- "Strike Two"
- "All right!"
Pressing switch 3 on the MPU should cause the sound system to play "FirePower-like" sounds continuously until power to the game is turned off.
Note that the sound subsystem can be configured to use either a 6808 or a 6802 microprocessor.
To use a 6808, jumper W1 should be in, W2 out.
To use a 6802, jumper W1 should be out, W2 in.
4.9 Replacing a System 8 MPU with a System 9 MPU
Yes, it's possible.
PDF Instructions (Document Source)
5 Repair Logs
Did you do a repair? Log it here as a possible solution for others.