Difference between revisions of "General"
Jump to navigation
Jump to search
m (→Lamp Chart) |
|||
| Line 28: | Line 28: | ||
!Life (hours) | !Life (hours) | ||
!Base | !Base | ||
| − | ! | + | !Typical Use |
|---- | |---- | ||
|44 | |44 | ||
| Line 74: | Line 74: | ||
Notes: | Notes: | ||
#47 lamp is often used as a replacement for 44 lamps where heat is a concern for backglass or plastics. | #47 lamp is often used as a replacement for 44 lamps where heat is a concern for backglass or plastics. | ||
| − | |||
===Lamp Sockets=== | ===Lamp Sockets=== | ||
Revision as of 07:56, 28 April 2011
1 Flippers
- How does a flipper work?
- Flippers have two coil windings, one is a high powered, low resistance winding, used for the power stroke (initial "flip"). The other is used to keep the flipper held up, when you are holding the flipper to trap a ball. There needs to be a mechanism to switch from the high powered side to the low powered side. The high powered side of the coil is almost a dead short, and anything other than a momentary activation would cause the fuse to blow.
- High Voltage flipper operation
- The original flipper operation was completely high voltage, requiring tungsten point contacts at the flipper switches and at the normally closed end of stroke switches. These switches need to be filed periodically and gapped correctly for proper operation. A maladjusted end of stroke switch can burn out a coil or a fuse as well as damage the plastic bobbin the coil is wrapped around, making for sluggish operation. Tarnished and burnt contacts at any point in the system can cause a weak flipper power stroke, making for diminished game play. Additionally, there are contacts on a machine's flipper relay that may need to be cleaned to provide the maximum power to the flippers. Connectors and header pins can also play a factor in a flipper's power; heavily tarnished connections will degrade performance.
- When you press a flipper button, you are actually grounding the flipper circuit, not providing the power. The power is already present at the coil's input lug. The power flows from the power supply to the flipper coil in the most direct path possible. The input lug has the solenoid power present, one wire going to one blade of the end of stroke switch, and one end of the hold winding. One end of the high powered coil's winding is attached to the other blade of the end of stroke switch.
- The flipper button has one contact attached to the terminus of both flipper coil windings; the other contact is attached to ground via the flipper relay. When the flipper relay is pulled in a ground path exists for the flipper, when it is deactivated (in game over/tilt modes) there is no ground path for the flippers. When you push the flipper button, the power travels through the end of stroke switch, the high powered coil, through the flipper cabinet switch and the relay to ground, pulling the flipper in with great force.
- A small arm on the pivot point of the flipper presses against the end of stroke switch outer blade, moving it away from the inner blade. This cuts the high power to the stroke side of the coil. Because the hold coil still is getting power via the input lug, the flipper will stay in an up position as long as you hold the button in. The hold coil has much greater resistance and so does not blow the fuse or create a short circuit.
- Solid State Flipper operation
- Solid state flippers do not refer to flippers in any solid state machine; rather, they refer to a design in later machines (post 1989) to eliminate the traditional high powered tungsten contacted type of flipper, which was subject to degradation over time. Less maintenance is required for solid state flippers.
- There are a few different designs to eliminate the high power switches used with flippers. One circuit monitors the time the flipper is held in; anything over 50-100 milliseconds continuous activation switches the power to the low side of the coil from the upper side electronically. Some designs of this nature also have a low powered normally open end of stroke switch, so that the flipper feels more like a traditional flipper. The time function of the solid state circuit only comes into play if the end of stroke switch is never detected, switching the power to the hold coil. Williams Fliptronics(tm) flippers operate in this fashion.
- Another design monitors the end of stroke switch/time and pulses the power supply to the flipper to reduce the voltage during the hold cycle. This allows a cheaper coil to be used as there is only one winding on the coil. Examples of this type of PVM flipper are late model Stern games. Sometimes the pulsing of the voltage causes the flipper to buzz slightly.
2 Lamp Chart
| Lamp | Voltage (V) | Current(A) | Candle Power | Life (hours) | Base | Typical Use |
|---|---|---|---|---|---|---|
| 44 | 6.3 | 0.25 | 0.9 | 3,000 | Miniature Bayonet (BA9) | Common GI bulb |
| 47 | 6.3 | 0.15 | 0.5 | 3,000 | Miniature Bayonet (BA9) | |
| 313 | 28 | 0.17 | 3.5 | 500 | Miniature Bayonet (BA9) | |
| 455 | 6.5 | 0.5 | N/A | 500 | Miniature Bayonet (BA9) | Flash Lamp |
| 555 | 6.3 | 0.25 | 0.9 | 3,000 | Wedge | Common GI bulb |
Notes:
- 47 lamp is often used as a replacement for 44 lamps where heat is a concern for backglass or plastics.