Burning EPROMS
Pinball machines use three types of programmable devices. By far the most common are EPROMs, used to store code, sound and graphics for solid state machines. The eraseable versions can be erased and re-used many times. Early machines use bipolar PROMs, devices that can be programmed only once. And many machines use programmable logic, with simpler devices (PALs and GALs) replacing a handful of TTL chips, and more complex devices carrying most of a video or sound subsystem.
For most people, programmers capable of handling mainstream EPROMs (2732 (32kb) - 27C080 (8Mb)) are sufficient.
Willem Programmers
These programmer are the least expensive available. They all run using open-source software. The simplest systems run from the parallel port and an external power supply, and have a tricky configuration using DIP switches and jumpers. Upgrades to the basic devices include USB power (you still need the parallel port); USB interface and power; and electronic configuration.
Recommended True USB version $80 - 120
Pocket Programmer
Designed and built in the U.S., these devices have been the standard for the industry. Programs 2708 with an adapter.
Recomended: USB version, about $270
Wellon Programmers
Designed and made in China,these devices use programmable pin drivers rather than TTL to program the parts. This approach means that Wellons can program a wider range of devices than other programmers, including PALs and GALs used in the logic of many modern machines. This is the author's preferred device because of its flexibility and up-to-date software and drivers (Windows 7 64 is supported).
Recommended: VP280, $120
Conitec programmers
Conitec has some very good programmers and their software is very clear and stable. Software upgrades are free as long as the programmer is supported by the newest software version. Conitec programmers support a lot of EPROM's (and other programmable's) and if needed you can request Conitec to add a device to the list. Their programmers don't come cheap but the programmer and software quality are excellent.
Recommended: Galep-5, USB, up to 48-pins devices, $499 Recommended: Galep-4, parallel port, up to 40-pins devices, $399
Batronix programmers
Batronix programmers have a good name, the software works good and stable. Their broad range starts with some low-cost affordable programmers and extends to models that can program 8 EPROM's at a time.
Recommended: BX32 Batupo, USB, up to 32-pins devices, $152
Elnec programmers
Elnec has very good programmers and software but they are actually quite expensive and therefore more suitable for production use. If you can get your hands on a used one for a reasonable price you'll have a great programmer.
There are significantly more expensive systems available that can program a full range of devices. However, these are unnecessary for most people, and the new low-cost programmer are just fine.
EPROMS
EPROMs are an obsolete technology, but were the standard for embedded code and data from the mid-1970s until the emergence of flash memory. They made sophisticated pinball systems possible, providing digital storage for code, sound and graphics. They work by injecting electrons into a charge storage area using a relatively high voltage. EPROM programmers must generate these voltages, which is why some early devices are not supported by all programmers.
There are 2 types of EPROM's available, OTP and UV. OTP means "One Time Programmable" and as the name suggests these can only be programmed once as they can not be erased. UV types have a window on top of the chip, this windows is made of quartz glass and below the window is the actual chip. When the chip is exposed to short-wave UV light for a specified amount of time (see device's datasheet) all the data will be erased and the device can be programmed again.
8-bit vs 16-bit EPROM's
Without goin to much into the details it's good to know that generally you will need 8-bit devices and NOT the 16-bit devices. They can be distinguished by the model number as well as the number of pins. In the list below are common model numbers of 8-bit EPROM's as well as some 16-bit EPROM's. For EPROM's in DIP packages; 8 bit EPROM's have 24, 28 or 32 pins whilst 16-bit devices have 42-pins. Other packages like surface mounted for instance are available but you will need the DIP versions.
EPROM model numbers The model number of an EPROM contains information about the manufacturer, capacity and access time along with some other information like the operating temperature range and package type. When selecting an EPROM it is important to have the right capacity and access time where the access time can be lower than needed but should not be higher!
Model number example: M27C4001-10F1 is a common model number and here's the break-down of the part number: -Letter(s) at the start for the manufacturer: M = ST Microelectronics (other examples are TMS for Texas Instruments and AM for AMD) -Numbers after the first letter(s) for the device type: 27 = EPROM -Letter for the supply voltage: C = 5V -Numbers for the capacity and memory organisation: 4001 = 4Mbit, 512kb x 8 (the 8 means it's an 8-bit device) -Numbers after the "-" for the access time: 10 means 100ns (12 for 120ns, 90 for 90ns and 80 for 80ns are also quite common) -Letter for the package: F means FDIP32W and that's a package with an erasing window (B would mean PDIP32 and would be an OTP version) -number for the temperature range: 1 means 0 to 70°C which is common Please note that some model numbers may contain extra letters containing more specifications.
Buying EPROMS
New EPROMS are very rare, but "pulls" - used EPROMs taken from obsolete electronic devices - are regularly available on eBay or from online sellers. The best pulls have been erased, tested, have had labels and residue removed, and their legs straightened. Expect to pay a little more for this service.
Erasing EPROMS
You don't have to have an EPROM eraser. But they are helpful if you need to erase some pulls that were not cleaned, programmed the wrong code, or want to recycle some parts. EPROM erasers use a short wavelength UV light to neutralize the charges stored in the EPROM cells. Cheap ones capable of doing a few EPROMS at a time are available for maybe $20. Much bigger erasers - used - pop up on eBay for about $50