Difference between revisions of "Indiana Jones: The Pinball Adventure"
m (→Game-Specific Issues: Moved IJ info from WPC page to this page) |
|||
| Line 27: | Line 27: | ||
=== Balls Continuously Served to the Shooter Lane === | === Balls Continuously Served to the Shooter Lane === | ||
| − | A failure certain to cause this behavior involves the "Ball Jam Opto", which is the last opto a ball passes as it's served from the trough to the shooter lane. If either the sending or receiving opto in the pair fails to work, the game will sense a jammed ball and continuously serve balls to the shooter lane. Sometimes the opto(s) fail outright. Sometimes the cause is a fractured solder joint or the OEM 270 ohm 1 Watt resistor on the sending side opto board. | + | A failure certain to cause this behavior involves the "Ball Jam Opto", which is the last opto a ball passes as it's served from the trough to the shooter lane. If either the sending or receiving opto in the pair fails to work, the game will sense a jammed ball and continuously serve balls to the shooter lane. Sometimes the opto(s) fail outright. Sometimes the cause is a fractured solder joint or the OEM 270 ohm 1 Watt resistor on the sending side opto board.<br> |
| + | |||
| + | Note that this failure isn't limited to Indiana Jones. Any game with this type of ball trough and a "jam opto", can exhibit this behavior. | ||
| + | <br clear=all> | ||
| + | |||
| + | === Path of Adventure Doesn't Move Left and Right Correctly === | ||
| + | |||
| + | The Path of Adventure is on the one hand, a very cool game feature, on the other hand, a bit of a booger to diagnose when not operating correctly. There are several possible problem causes. | ||
| + | |||
| + | [[File:IJPOAOptoBoardInSitu.jpg|200px|thumb|left|The Path of Adventure opto board, in situ.]]<br> | ||
| + | '''Failed Limiting Opto Board<br>''' | ||
| + | The POA opto board tells the MPU that the POA has reached either it's left or it's right limit. If one/both of these optos fail, the game won't know if/when limit has been reached. Testing these optos is easy, once the POA has been removed. You may be able to use the dedicated POA ("Mini Playfield") test in the test menu. | ||
| + | <br clear=all> | ||
| + | |||
| + | [[File:WPCType2FlipperOptoBoard.jpg|200px|thumb|left|An example type 2 cabinet flipper switch opto board, in situ.]]<br> | ||
| + | '''Flakey Cabinet Flipper Switch Optos<br>''' | ||
| + | This one is a bit tough to understand. While the flippers may work perfectly in game play, if the opto is just a bit flakey, the POA may "stutter" in one direction or the other. It may not move at all. You can swap the left and right flipper opto boards to see if the problem follows. Often, cleaning the optos on the flipper board will solve the problem. | ||
| + | <br clear=all> | ||
| + | |||
| + | === Removing the Path of Adventure === | ||
| + | |||
| + | It's sometimes necessary to remove the POA to replace lamps (this would be a GREAT place to use LEDs) or repair switches. Removing the Path of Adventure is much simpler than one might assume. | ||
| + | |||
| + | <center> | ||
| + | <gallery widths=300px heights=300px perrow=2 caption="Steps to Remove the Path of Adventure"> | ||
| + | File:IJRearChannel.jpg|<center><b>1. Remove the two screws that secure the rear channel that leads to the POA.</b></center> | ||
| + | File:IJPOABypassLane.jpg|<center><b>2. Remove the two screws that secure the left "POA Bypass Channel". The front screw is pictured.</b></center> | ||
| + | File:IJPOABracket.jpg|<center><b>3. Once the bypass channel is removed, the front bracket will be exposed. Remove these two screws.</b></center> | ||
| + | File:IJPOASetScrew.jpg|<center><b>4. Loosen the "set screw" that attaches the POA to the motor shaft with a 5/64" hex wrench.</b></center> | ||
| + | </gallery> | ||
| + | </center> | ||
<br clear=all> | <br clear=all> | ||
Return to [[Williams WPC]] page. | Return to [[Williams WPC]] page. | ||
Revision as of 05:56, 18 September 2014
 |
| Manufacturer | System | Year | Model | Produced |
|---|---|---|---|---|
| Williams | WPC - DSC Sound | 1993 | 50017 | 12,716 |
Indiana Jones: The Pinball Adventure Playing Tips and Rule Sheet
Indiana Jones: The Pinball Adventure Shop Guide
1 WPC Specific Issues
2 Game-Specific Issues
2.1 Path of Adventure Switch shorts causing extra balls to be served
The front right switch on the path of adventure gets hit underneath by balls hopping around the "Mode Start" hole. This shorts the wires/diode/switch lugs. This switch is on the same row or column as the ball jam opto. This is the last opto a ball passes as it is served to the shooter lane. If you are getting extra balls kicked up to the shooter lane, that front right switch is a good place to start.
2.2 Balls Continuously Served to the Shooter Lane
A failure certain to cause this behavior involves the "Ball Jam Opto", which is the last opto a ball passes as it's served from the trough to the shooter lane. If either the sending or receiving opto in the pair fails to work, the game will sense a jammed ball and continuously serve balls to the shooter lane. Sometimes the opto(s) fail outright. Sometimes the cause is a fractured solder joint or the OEM 270 ohm 1 Watt resistor on the sending side opto board.
Note that this failure isn't limited to Indiana Jones. Any game with this type of ball trough and a "jam opto", can exhibit this behavior.
2.3 Path of Adventure Doesn't Move Left and Right Correctly
The Path of Adventure is on the one hand, a very cool game feature, on the other hand, a bit of a booger to diagnose when not operating correctly. There are several possible problem causes.
Failed Limiting Opto Board
The POA opto board tells the MPU that the POA has reached either it's left or it's right limit. If one/both of these optos fail, the game won't know if/when limit has been reached. Testing these optos is easy, once the POA has been removed. You may be able to use the dedicated POA ("Mini Playfield") test in the test menu.
Flakey Cabinet Flipper Switch Optos
This one is a bit tough to understand. While the flippers may work perfectly in game play, if the opto is just a bit flakey, the POA may "stutter" in one direction or the other. It may not move at all. You can swap the left and right flipper opto boards to see if the problem follows. Often, cleaning the optos on the flipper board will solve the problem.
2.4 Removing the Path of Adventure
It's sometimes necessary to remove the POA to replace lamps (this would be a GREAT place to use LEDs) or repair switches. Removing the Path of Adventure is much simpler than one might assume.
- Steps to Remove the Path of Adventure
1. Remove the two screws that secure the rear channel that leads to the POA. 
2. Remove the two screws that secure the left "POA Bypass Channel". The front screw is pictured. 
3. Once the bypass channel is removed, the front bracket will be exposed. Remove these two screws. 
4. Loosen the "set screw" that attaches the POA to the motor shaft with a 5/64" hex wrench.
Return to Williams WPC page.