Difference between revisions of "Haunted House"
| (2 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
= Sound Mapping for Haunted House = | = Sound Mapping for Haunted House = | ||
| − | + | [[File:YT.png]] A video demonstrating each sound made by the 32 possible bit patterns for S1 through S16 can be found [https://www.youtube.com/watch?v=RjMQT5kao4Y&t=6s <b><u>here</u></b>]. | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | [[File:YT.png]] A video demonstrating each | ||
| − | |||
| − | |||
=Replacing Haunted House Lower Playfield Illumination Lamps with #44 Lamps= | =Replacing Haunted House Lower Playfield Illumination Lamps with #44 Lamps= | ||
| Line 79: | Line 28: | ||
<b>Let there be light...</b><br> | <b>Let there be light...</b><br> | ||
All finished with the mod. The bulbs now will light on 6VDC instead of 24VDC. Swap out all of those #313s with #44s or #47s and never worry about looking for the correct bulb again.<br clear=all> | All finished with the mod. The bulbs now will light on 6VDC instead of 24VDC. Swap out all of those #313s with #44s or #47s and never worry about looking for the correct bulb again.<br clear=all> | ||
| + | |||
| + | =Kicking target switch arcing capacitor= | ||
| + | [[File:Kickingtargetcaps.jpg|thumb|left|300px|Kicking target capacitors]] | ||
| + | The main playfield circuit diagram shows a 3.3uF capacitor across the coil for each of the four kicking targets and rubber. | ||
| + | However, on at least | ||
| + | one machine, these were missing. The positive terminal of the capacitor goes to the cathode of the diode on the coil contacts. The photograph shows the left side targets with the capacitors added, plus the holders for the 3A slo-blo fuses recommended in one of | ||
| + | Clay's Guides. | ||
Latest revision as of 18:39, 18 November 2023
1 Sound Mapping for Haunted House
A video demonstrating each sound made by the 32 possible bit patterns for S1 through S16 can be found here.
2 Replacing Haunted House Lower Playfield Illumination Lamps with #44 Lamps
This modification documented by Chris Hibler, based on Black Hole mod developed by Steve Charland.
When Gottlieb® designed Black Hole and Haunted House, the designers chose to illuminate the lower playfield with 313 lamps, which are 28 volt lamps. Coil power could be used as a power source, and the lamps are slightly brighter than #44 lamps. However, #313 bulbs are triple the price of #44 lamps and are a unique part to stock.
Converting the power circuit that drives these lamps to 6VDC makes sense and allows the use of the more common #44 lamps.
The big picture...
U relay mods...
Remove the...
Solder a new 16 gauge wire to the vacant solder tab where 388 wire was removed.
Attaching to the power bus...
Solder the...
Use "zip ties" to secure the new wire to the factory wire bundle. You can feed the wire through the factory "tie downs".
Let there be light...
All finished with the mod. The bulbs now will light on 6VDC instead of 24VDC. Swap out all of those #313s with #44s or #47s and never worry about looking for the correct bulb again.
3 Kicking target switch arcing capacitor
The main playfield circuit diagram shows a 3.3uF capacitor across the coil for each of the four kicking targets and rubber. However, on at least one machine, these were missing. The positive terminal of the capacitor goes to the cathode of the diode on the coil contacts. The photograph shows the left side targets with the capacitors added, plus the holders for the 3A slo-blo fuses recommended in one of Clay's Guides.