Difference between revisions of "Stern SPIKE™ System Repair"
(→Technical Info: add information about spike 2 linux distro) |
|||
| Line 83: | Line 83: | ||
|- | |- | ||
| 2020 || [[Teenage Mutant Ninja Turtles (Stern)]] || Yes || Yes || Yes (500 max) || | | 2020 || [[Teenage Mutant Ninja Turtles (Stern)]] || Yes || Yes || Yes (500 max) || | ||
| + | |- | ||
| + | | 2020 || [[The Avengers Infinity Quest]] || Yes || Yes || Yes (500 max) || | ||
| + | |- | ||
| + | | 2020 || [[Led Zeppelin]] || Yes || Yes || Yes (500 max) || | ||
| + | |- | ||
| + | | 2021 || [[Star Wars The Mandalorian]] || Yes || Yes || Yes (750 max) || | ||
| + | |- | ||
| + | | 2021 || [[Godzilla]] || Yes || Yes || Yes (1000 max) || | ||
|} | |} | ||
Revision as of 20:31, 27 October 2021
 |
Click to go back to the Data East/Sega/Stern pinball repair guides index.
1 Stern SPIKE™ System Repair
1.1 Introduction
The SPIKE™ System is the current board system used by Stern Pinball. The first full production game to use the SPIKE Board Set was Wrestlemania in 2015. The SPIKE architecture is a large departure from prior board set architectures. Per Stern, "The SPIKE Pinball system is rugged, distributed, and embedded platform custom-designed for the rigors of the pinball machine environment".
The SPIKE system is comprised of a CPU board and a series of several "node boards" that are powered from a 48VDC power bus. Each SPIKE "node board" will regulate this 48VDC down to the proper voltage required to operate the "devices" under control of that node (lamps, coils, switches, etc). Nodes are connected with standard CAT 5e (or better) 8 conductor Ethernet wiring although the interface protocol is not Ethernet, and connecting a SPIKE node to computer Ethernet will damage the board (per Stern). There are several node boards mounted to the bottom side of the playfield to control the various lamps, coils, and switches on the playfield. There is one "cabinet" node board located next to the plumb bob tilt assembly which controls start button, tilt, coin door, diagnostic switches, dollar bill acceptor, shaker motor, ticket dispenser, coin meters, etc.
1.2 Games
1.2.1 SPIKE 1
| Date | Name | Pro | Premium | Limited Edition |
|---|---|---|---|---|
| 2012 | Transformers, The Pin | One Model | ||
| 2013 | Avengers, The Pin | One Model | ||
| 2015 | Wrestlemania | Yes | No | Yes (400 max) |
| 2015 | Whoa Nellie! Big Juicy Melons™ | One Model | ||
| 2015 | KISS | Yes | Yes | Yes (600 max) |
| 2015 | Game of Thrones | Yes | Yes | Yes (700 max) |
| 2016 | Ghostbusters | Yes | Yes | Yes (500 max) |
| 2016 | Pabst Can Crusher | One Model | ||
| 2016 | Spider-Man, The Pin | One Model | ||
| 2018 | Primus | One Model | ||
| 2018 | Supreme | One Model | ||
1.2.2 SPIKE 2
| Date | Name | Pro | Premium | Limited Edition | Other Models |
|---|---|---|---|---|---|
| 2016 | Batman 66 | Yes | Yes (240 max) | Super LE (80 max) | |
| 2017 | Aerosmith | Yes | Yes | Yes (500 max) | |
| 2017 | Star Wars (Stern) | Yes | Yes | Yes (800 max) | |
| 2017 | Guardians of the Galaxy | Yes | Yes | Yes (600 max) | |
| 2018 | Iron Maiden (Stern) | Yes | Yes | Yes (500 max) | |
| 2018 | Deadpool | Yes | Yes | Yes (500 max) | |
| 2018 | Beatles | Gold (1614 max) | Platinum (250 max) | Diamond (100 max) | |
| 2019 | The Munsters | Yes | Yes | Yes (600 max) | |
| 2019 | Black Knight: Sword of Rage | Yes | Yes | Yes (600 max) | |
| 2019 | Jurassic Park (Stern) | Yes | Yes | Yes (500 max) | |
| 2019 | Star Wars Pin | One Model | |||
| 2019 | Elvira's House of Horrors | Yes | Yes (400 max) | Signature Edition (50 max) | |
| 2019 | Stranger Things | Yes | Yes | Yes (500 max) | |
| 2020 | Heavy Metal | One Model | |||
| 2020 | Teenage Mutant Ninja Turtles (Stern) | Yes | Yes | Yes (500 max) | |
| 2020 | The Avengers Infinity Quest | Yes | Yes | Yes (500 max) | |
| 2020 | Led Zeppelin | Yes | Yes | Yes (500 max) | |
| 2021 | Star Wars The Mandalorian | Yes | Yes | Yes (750 max) | |
| 2021 | Godzilla | Yes | Yes | Yes (1000 max) | |
1.3 Technical Info
1.3.1 The SPIKE Board Set
Stern has issued a technical video discussing the Spike 1 system boards: https://www.youtube.com/watch?v=MvefdrNaAPg
There is a well done video by Stern, featuring George Gomez, describing the Spike 2 system boards:
https://www.youtube.com/watch?v=d1xdmgeAylQ&t=190s
Spike 1 CPU board installed in a Ghostbusters.
1.3.2 Recommended Documentation
1.3.2.1 Manuals
As always, it is highly recommended to possess a game manual. Every game manual is full of detailed information regarding game specific switch, lamp, and coil assignments. Equally, details for maneuvering through test, audit, and bookkeeping screen menus, schematics for all boards used, and game specific mechanical assemblies are included.
- Game of Thrones manuals - Pro, Premium & LE
- Ghostbusters manuals - Pro, Premium & LE
- Aerosmith manuals - Pro, Premium & LE
- Star Wars manuals - Pro, Premium & LE
- Iron Maiden manuals - Pro, Premium & LE
- Deadpool manuals - Pro, Premium & LE
- Beatles manuals - Gold/Platinum/Diamond
- The Munsters manuals - Pro, Premium & LE
- Black Knight: Sword of Rage manuals - Pro, Premium & LE
- Jurassic Park manuals - Pro, Premium & LE
- Star Wars Pin - Manual
- Elvira's House of Horrors - Premium, LE, & SE
- Stranger Things manuals - Pro, Premium & LE
- Teenage Mutant Ninja Turtles manuals - Pro
1.3.2.2 Schematics
1.3.2.2.1 SPIKE 1
| Game | 520-6936-01 SPIKE-1 CPU Node Board |
520-5319-00 Cabinet Node Board |
520-6967-xx Cabinet Node Board |
520-6935-10 8-Coil Playfield Node Board |
520-6985-72 8-Coil Playfield Node Board |
520-5322-00 32-Light & Switch Node Board |
520-5329-10 4-Coil Playfield Node Board |
520-5345-01 Trough Serial Opto Receiver Extension Board |
Misc. |
|---|---|---|---|---|---|---|---|---|---|
| Whoa Nellie | Node 0 | Node 1 | Node 8 | Node 10 | Node 9 & 11 | ||||
| KISS Prem/LE | Node 0 | Node 1 | Node 8, 9, & 10 | Node 11 | 8a | ||||
| Game of Thrones Prem/LE | Node 0 | Node 1 | Node 8 & 11 | Node 9 & 10 | 8b | ||||
| Ghostbusters Prem/LE | Node 0 | Node 1 | Node 8 & 9 | Node 10 | 8a | Node 24 - 520-6988-00 LCD Node (Ecto Goggles) |
1.3.2.2.2 SPIKE 2
| Game | 509-1000-00 SPIKE-2 CPU Node Board |
509-1003-01 SPIKE-2 CPU Node Board |
520-6967-xx Cabinet Node Board |
520-7017-72 8-Coil Playfield Node Board |
520-6998-72 4-Coil Playfield Node Board |
520-6976-72 SPI Core Playfield Node Board |
520-7001-00 Trough Serial Opto Receiver Extension Board |
520-6996-00A Motor Driver Board |
Misc. |
|---|---|---|---|---|---|---|---|---|---|
| Batman 66 | Node 0 | Node 1 | Node 8 & 9 | 8a | 9c | Node 10 - 520-7019-72 Turntable Node, Node 24 - LCD Node (Villain Vision) | |||
| Aerosmith | Node 0 | Node 1 | Node 8 & 9 | 8a | 8e | Node 10 - 520-5329-10 Playfield 48V 4-Coil node board (Prem/LE only) | |||
| Star Wars Prem/LE | Node 0 | Node 1 | Node 8 & 9 | Node 11 (Prem/LE only) | Node 10 | 8a | 9d | ||
| Guardians of the Galaxy Prem/LE | Node 0 | Node 1 | Node 8 & 9 | Node 11 | Node 10 | 8a | 9b | ||
| Iron Maiden Pro | Node 0 | Node 1 | Node 8 & 9 | 8a | |||||
| Deadpool Pro | Node 0 | Node 1 | Node 8 & 9 | 8a | |||||
| Beatles | Node 0 | Node 1 | Node 8 & 9 | 8a | |||||
| Munsters Prem/LE | Node 0 | Node 1 | Node 8 & 9 | 8a | |||||
| Black Knight: Sword of Rage | Node 0 | Node 1 | Node 8 & 9 | 8a | |||||
| Jurassic Park | Node 0 | Node 1 | Node 8 & 9 | 8a | |||||
| Star Wars Pin | Node 0 | Node 8 | 8c | ||||||
| Stranger Things | Node 0 | Node 1 | Node 8 & 9 | 8a | |||||
| Teenage Mutant Ninja Turtles Pro | Node 0 | Node 1 | Node 8 & 9 | 8a |
Notes:
- 509-1000-00 replaced by 509-1003-01
- For the Star Wars Pin (Home Edition), Node 8 subsumes the functions performed by the cabinet node board (typically Node 1 on other Spike machines).
1.3.3 Accessing Bookkeeping, Settings, and Diagnostic Modes
Spike system games use four pushbutton switches (located on the coin door) to access the bookkeeping, adjustments, and diagnostics very much like Williams WPC series machines do. The black pushbutton enters the menu while the two red + and - pushbuttons step you through the menu (also act as volume up and volume down). If you want to go backwards, push the green button (it acts like "escape" function).
1.3.4 Cabinet Node Board Information
LED indicators on the board:
- Red: 48 volts is present at the board
- Yellow: Board is communicating with cpu board
- Green: 6 volts is present at the board
Ghostbusters # 520-6967-00 (replaced by 520-6967-72) Cabinet Node Board connectors:
- CN1: Universal Card link (if present on your particular board)
- CN2: Low tickets warning in ticket dispenser
- CN3: To Meter #1 (usually coin counter, use a 12 volt meter)
- CN4: To Meter #2 (usually tickets out, use a 12 volt meter)
- CN5: From Coin Door coin switches and coin entry LED lights
- CN6: Left cabinet switch inputs (tilt, start, etc)
- CN7: Right cabinet switch inputs
- CN8: From electronic coin mechanism (for export machines only)
- CN9: From Dollar Bill Acceptor
- CN10: From coin door volume and diagnostic switches
- CN11: Ticket dispenser
- CN12: Volume and diagnostic switches output to cpu board connector CN25
- CN13: RJ45 Node Data Bus
- CN14: 48 volts DC power input
- CN15: Optional spare LED +5 volt power source
- CN16: To shaker motor
1.3.5 Dollar Bill Acceptors
The Spike system machines come with a bill acceptor coin door and dollar bill acceptor wiring harness already installed. Many are wired for using 120 volts AC powered bill acceptors (Mars/MEI AE-2411-300 is recommended), but there are reports some machines are wired for 12 volts DC models instead. Here is a Ghostbusters which comes wired for 120 volts AC power for the bill acceptor.
1.3.6 Optional Equipment
This power supply for 12 volt and 5 volt accessory items has four Molex output jacks and is fused:
Power supply for backbox mounting
This power supply is the same as above except it mounts in the lower cabinet near the cashbox:
Power supply for lower cabinet mounting
This 8 way splitter provides eight 12 volt only Molex jacks and mounts only in the backbox:
8 Way splitter for backbox mounting
Knocker Kit provides a real knocker:
Real Knocker Kit for Spike 1 and Spike 2
1.3.7 Linux OS
Spike's central CPU node in the backbox runs Linux. The hardware is a derivative of the NXP i.MX6 Wandboard.
The SD card has ext4 partitions, the most interesting being the root filesystem and /games. The rootfs contains a yocto build with no toolchain or kernel headers, but cross-compilation is possible using gcc-arm-linux-gnueabihf.
There is a serial console on connector CN2. This connector is generally not populated. It's also possible to configure the Ethernet port for remote access.
The game executable has a text-based interactive debug interface with some interesting options:
commands:
adj: perform operations on adjustments.
amp: amp system interface.
aud: perform operations on audits.
coil: fire a coil.
credit: manipulate credits.
debug: get debug information.
display: display system interface.
dsp: DSP interface.
knocker: perform operations on the knocker.
le: lamp effect system interface.
mode: interact with modes.
node: node diagnostics commands.
nv: get non-volatile ram info.
proc: get information about processes.
red: redemption interface.
replay: replay interface.
scene_cache: scene cache system interface.
score: manipulate player scores.
sound: sound system interface.
textsafe: show text safe region.
video_display: video display system interface.
Some more information can be found here:
* https://docs.missionpinball.org/en/latest/hardware/spike/connection.html * https://pastebin.com/raw/RryUb8iC
1.4 Problems and Solutions
1.4.1 Power Problems
The main power supply is 48 volts @ 10.5 amps and has a cooling fan. Some versions have the fan on the front of the power supply while others may have the fan mounted on the top. Power supply is a Mean Well # RSP-500-48 (Jameco Electronics # 2198014).
Ghostbusters wiring interconnection label.
1.4.1.1 Noisy Power Supply Fan
There have been reports of the fan on the switching regulator 48 volt power supply becoming too loud. There is now a plug n play replacement fan kit. The fan in the kit is a lot quieter.
1.4.1.2 Relocating the Power Switch
One complaint with Spike machines is the fact the power on-off switch is located in the backbox. If the machine is located in a bank of machines, it may be difficult to reach the power switch. Some people have ordered a Stern # 515-7085-00 Power Switch and Bracket assembly and mounted it in the usual right front bottom cabinet location. Then wires are run up to the backbox and connected in place of the backbox power switch. Stern installs a shaker motor in the right front of the cabinet now. So the shaker motor (if installed) must be relocated farther back in the cabinet (about 6 inches) to the other side of the wooden divider.
Stern Power Switch and Mounting Bracket Assembly
1.4.2 MPU boot issues
If the MPU doesn't boot, check that the memory card is firmly seated in its slot on the MPU board. Also, you can try re-seating the memory card. Sometimes this fixes Spike games that won't boot.
1.4.3 Game resets
Some reset/slam tilt problems have been traced to the shaker motor. Please check the service advisory bulletin.
1.4.4 Solenoid problems
1.4.5 Lamp problems
1.4.6 Switch problems
1.4.7 Display problems
Starting with Pirates of the Caribbean (a S.A.M. board set game), Stern replaced the normal Plasma Dot Matrix Display on European models with an LED variant because of the RoHS law. They first used PinLED DMDs, and later, switched to a red DMD specifically made for them (520-5052-05). The debate which looks better will be going on for your remaining lifetime and continue right into your next few lives.
1.4.7.1 LED DMD bad vertical line
If a game is always showing a semi-bright vertical line on the DMD, usually one of the LED segments is bad. Fortunately the bad segment can be found easily. As shown in the picture to the left, one pixel in the line is always dark. This 8x8 segment is the bad guy and needs to be replaced. The good thing is that this problem usually occurs with NIB games just after a few hours or days of game play so the DMD is still under warranty. If not, ask Stern for the availability of the LED segments. When replacing a block, be advised that the vias are small and are difficult to remove without the proper equipment.
1.4.8 Sound problems
The Spike 1 cpu board connector CN1 is the 2 channel backbox speaker output (two 4 ohm @ 10 watt 4 inch square speakers, use Stern # 031-5004-02). Connector CN4 is the lower cabinet woofer speaker output (one 8 ohm @ 20 watt 8 inch round speaker, use Stern # 031-5007-01).
CN1 pinout:
- 1: Black-White backbox right speaker -.
- 2: Red-White backbox right speaker +.
- 3: Key
- 4: Black backbox left speaker -.
- 5: Red backbox left speaker +.
CN4 pinout:
- 1: Yellow-Black lower cabinet woofer speaker output -.
- 2: Yellow-White lower cabinet woofer speaker output +.
CN18 (TRS headphone 3.5mm jack) pinout:
- TIP: headphone left, 8 ohm, 200mw maximum output
- RING: headphone right, 8 ohm, 200mw maximum output
- SLEEVE: Audio ground
CN27 Preamp (line) output to feed sound to an external monaural amplifier or subwoofer amplifier:
- 1: Line out +, 600 ohms
- 2: Line out ground
- 3: Line out -, 600 ohms
The latest game codes now have speaker impedance settings for whether 4 ohm or 8 ohm speakers are installed in the machine. Added UTIL->VOL adjustments, Speaker Balance, backbox speaker type, and cabinet speaker type for Spike 1 and 2 games.
1.4.9 Flipper problems
See Common Flipper Troubleshooting for general flipper information.
1.4.10 Pop bumper problems
1.4.11 Opto problems
1.4.12 Shaker Motor Problems
The shaker motor connects to connector CN16 (CN2 on early boards) on the cabinet node board located next to the plumb bob tilt. It will be labeled Shaker Motor.
The pinout of CN16 is this:
- 1: Shaker motor - (Blue wire)
- 2: Shaker motor - (optional extra connection)
- 3: Shaker motor + (optional extra connection)
- 4: Key
- 5: Shaker motor + (Red wire)
Genuine Stern SPIKE Shaker motor causes mysterious slam tilts during game:
If your shaker motor is damaged or worn out, you can purchase just the motor itself if desired.
Replacement Spike/Sam shaker motor only
1.4.12.1 Third Party Shaker Motors
All current SPIKE™ games allow for a shaker motor, but it should be a SPIKE shaker motor, not a SAM-system shaker motor (SAM is the previous system). After the initial launch of SPIKE™ games, it was discovered that motors from third-party manufacturers (in particular Pinball Life) had a capacitor that caused problems, and will blow out the node board. Service Bulletin 184 advises against using third-party shaker motors entirely. Installation will void the game's warranty.
The symptom of this problem is that the Start button, plumb bob, and coin door GI lamps won't work; that is, the game becomes unplayable.
Some owners have reported that removing the capacitor from the third-party motor will fix the problem. Stern's public position is that owners should spend the extra money and buy an OEM motor. Many vendors do not clearly differentiate between an OEM part and a third-party part.
Genuine Stern Spike shaker motor kit
Third party Spike shaker motor kit
All SPIKE system games already have the holes for a shaker motor pre-drilled and 10-32 T-Nuts already installed for mounting the shaker motor to the right of the cashbox.
1.4.13 Missing Playfield Slide Brackets on Pro Models
Starting with the Pro model of WWE, Stern removed the playfield slide brackets and replaced them with a couple of cheap pieces of threaded rod covered in heat shrink tubing and a ball shooter tip. This was so you could pull the playfield toward you a bit and rest those "pegs" on the lockdown receiver to service under the playfield. That didn't work very well if you needed to get to something at the very back of the playfield. Pinball Life has reproduced the playfield slide brackets as a set. Once installed, the playfield can be pulled out a lot farther to make it easier to work at the rear of the playfield. Premium and LE models already have the playfield slide brackets installed.
Spike cabinet playfield slide bracket kit
Note: It now appears, starting with Iron Maiden, that Stern has gone back to installing the metal slide brackets on the bottom of the playfields on Pro models.
1.5 References
1.6 Game Specific Problems and Fixes
Ghostbusters Premium and LE models damaged Ecto Goggles LCD screen. Air balls flying up and hitting/damaging the LCD screen on the Ecto Goggles unit. Stern issued a service bulletin about this problem and came up with a metal shield to install on the machine to prevent this from happening.