Difference between revisions of "Gottlieb System 3"

From PinWiki
Jump to navigation Jump to search
Line 58: Line 58:
 
Possibly doesn't apply to some, can't think of an example.
 
Possibly doesn't apply to some, can't think of an example.
  
==Game Specific Problems and Fixes==
+
On Stargate (and probably some other games like Big Hurt) you are occasionally asked to answer a question with the flipper buttons.  The flippers still work but the button selection doesn't.  What has happened is one of the wires at the coil has probably broken lose.  On my Stargate, I could select with the left button but not the right button, but all flippers still worked.  Searching underneath revealed the broken wire.
Example would be servo controller on Independence Day pinball
+
 
 +
Stargate--left upkicker can't get the ball up to the ramp.  Upgrading to the strongest coil will solve the problem.
 +
 
 +
Stargate--On the shot along the far right side, it will occasionally get rejected.  Putting in blue foam in the back will stop the rejections.
 +
 
 +
Stargate 'stuck in tourney mode' or something like that.  There is a daisy chain of wires going from the playfield to the tourney mode switch.  If one of those wires breaks off (like on one of the kickers) the game may get stuck in tourney mode or something along those lines.
 +
 
 +
Stargate--drop targets not resetting during gameplay.  This is simply a cleaning issue.  When the drop targets get dirty, the coil doesn't always have enough power to reset them.  Cleaning the targets fixes the issue.
  
 
==Repair Logs==
 
==Repair Logs==
 
Did you do a repair? Log it here as a possible solution for others.
 
Did you do a repair? Log it here as a possible solution for others.

Revision as of 21:04, 28 April 2011

ExclamationPoint.jpg
Note: This page is a work in progress. Please help get it to a completed state by adding any useful information to it.


1 Introduction

Put system info here

2 Games

2.1 Alpha-Numeric

  • Lights Action Camera
  • Sliver Slugger
  • Vegas
  • Deadly Weapon
  • Title Fight
  • Nudge-It
  • Bell Ringer
  • Car Hop
  • Hoops
  • Cactus Jack
  • Class of 1812
  • Amazon Hunt III
  • Surf'n Safari
  • Caribbean Cruise
  • Operation Thunder

2.2 Dot Matrix

  • Super Mario Bros
  • Super Mario Bros: Mushroom World
  • Cue Ball Wizard
  • Street Fighter II
  • Tee'd Off
  • Gladiators
  • Wipe Out
  • World Challenge Soccer
  • Rescue 911
  • Freddy: a Nightmare on Elm Street
  • Shaq Attaq
  • Stargate
  • Big Hurt
  • Waterworld
  • Strikes N Spares
  • Mario Andretti
  • Barb Wire
  • Brooks & Dunn
  • Casino Royale

3 Technical Info

Things like Data East's controller board was a copy of William's System 11 with some changes would go here.

4 Problems and Fixes

4.1 Power Driver Issues

This may not apply to some, as MPU might have been part of it.

4.2 MPU Issues

4.3 Power Supply Issues

4.4 Display Driver Board

Possibly doesn't apply to some, can't think of an example.

On Stargate (and probably some other games like Big Hurt) you are occasionally asked to answer a question with the flipper buttons. The flippers still work but the button selection doesn't. What has happened is one of the wires at the coil has probably broken lose. On my Stargate, I could select with the left button but not the right button, but all flippers still worked. Searching underneath revealed the broken wire.

Stargate--left upkicker can't get the ball up to the ramp. Upgrading to the strongest coil will solve the problem.

Stargate--On the shot along the far right side, it will occasionally get rejected. Putting in blue foam in the back will stop the rejections.

Stargate 'stuck in tourney mode' or something like that. There is a daisy chain of wires going from the playfield to the tourney mode switch. If one of those wires breaks off (like on one of the kickers) the game may get stuck in tourney mode or something along those lines.

Stargate--drop targets not resetting during gameplay. This is simply a cleaning issue. When the drop targets get dirty, the coil doesn't always have enough power to reset them. Cleaning the targets fixes the issue.

5 Repair Logs

Did you do a repair? Log it here as a possible solution for others.