Difference between revisions of "MPU Battery Replacement Options"
(→WPC: games with a real time clock) |
|||
| Line 46: | Line 46: | ||
===Generation 2/3=== | ===Generation 2/3=== | ||
| + | |||
| + | ==Alvin G== | ||
| + | * Remote Battery | ||
==Atari== | ==Atari== | ||
| Line 75: | Line 78: | ||
==GamePlan== | ==GamePlan== | ||
| − | + | * Remote Battery | |
| + | * NVRAM (not fully tested) | ||
==Gottlieb== | ==Gottlieb== | ||
Revision as of 13:07, 12 January 2016
1 Introduction
RAM chips are typically used to store game settings and bookeeping data. However, RAM is volatile and can only store data if power is applied to the chip. If power is lost, so is the data. So, the solution to this was to include a battery on the MPU to retain the data in RAM when the game was turned off.
Unfortunately, many of these batteries leak and damage or destroy circuit boards in the process. So, it is imperative that the battery is removed from the MPU in order to prevent this damage in the future.
In order to retain the data for game settings and bookeeping, there are a few different options to replace the original battery and prevent future problems from leakage.
1.1 Remote Battery Pack
The remote battery solution is when a battery pack is installed in a game, but lead wires are attached to the positive and negative solder points on the MPU. The safest place to mount a remote battery pack is below any circuit boards and as far away from them as possible, so as to avoid escaping gas and drippings from leaks.
1.2 Lithium Battery
Classic Williams games had a build-in battery holder that could fit AA batteries. Unfortunately, it was common to see standard alkaline batteries used in these holders, which always leaked.
Lithium batteries are produced in the AA battery footprint, so can be installed in the battery holders used on classic Williams MPUs. Lithium batteries are less prone to leaking, but it is still a good idea to mount them off the MPU in a remote battery pack.
Installing batteries directly onto the MPU leaves the game open to the possibility of an owner replacing a dead AA lithium battery with a AA alkaline battery if they don't have a lithium battery on-hand because it's the easy and lazy thing to do. As a result, battery leakage becomes a serious risk again.
1.3 Memory Capacitor
Memory capacitors are special capacitors that hold a charge for an extended period of time and take the place of a battery. The downside is that the game has to be turned on at least once for several hours every 14-30 days in order to build up to a full charge.
Additionally, lower quality capacitors are prone to leaking, though not as spectacularly as alkaline or NiCad batteries.
At this point, memory capacitors have fallen from favor because of the introduction and economical prices of lithium batteries, coin cell batteries, and NVRAM.
1.4 Coin Cell / Button Battery
Lithium coin cell batteries (also known as button batteries) are much less prone to leakage than the batteries originally used on MPUs. They typically have a 10-year life span when used on an MPU. Gottlieb System 3 MPUs were the first to utilize coin cell batteries.
1.5 NVRAM
NVRAM (non-volitile RAM) is being used to replace volatile RAM installed on the MPU. Volatile RAM can only store data if power is applied to the chip. If power is lost, so is the data. NVRAM can retain data without needing any power. It is essentially "frozen" in the chip.
Various game systems use different types of RAM, so adapters are needed to adapt the footprint and pinout of the 6264 NVRAM pinout to the RAM footprint/socket that the game system is using.
NVRAM adapters typically list which RAM socket and/or game systems they are intended to support.
2 Game Systems
2.1 Allied Leisure
2.1.1 Generation 1
Game data is not saved. A battery solution is not necessary.
2.1.2 Generation 2/3
2.2 Alvin G
- Remote Battery
2.3 Atari
2.3.1 Generation 1
Game data is not saved. A battery solution is not necessary.
2.3.2 Generation 2
2.4 Bally
2.4.1 -17/-35/-133 MPU
- Remote Battery
- Memory Capacitor
- Coin Cell Battery
- NVRAM
2.4.2 6803 MPU
2.5 Capcom
- NVRAM
2.6 Data East
- Remote Battery
- Memory Capacitor
- Coin Cell Battery
- NVRAM
2.7 GamePlan
- Remote Battery
- NVRAM (not fully tested)
2.8 Gottlieb
2.8.1 System 1
- Remote Battery
- Coin Cell Battery
NVRAM adapters are not currently available for System 1 games due to the mismatch between the address lines used on the MPU and standard 6264-based NVRAM.
2.8.2 System 80/80A/80B
- Remote Battery
- Memory Capacitor
- Coin Cell Battery
- NVRAM
2.8.3 System 3
- Remote Battery
- Coin Cell Battery
2.9 Heighway Pinball
2.10 Jersey Jack Pinball
2.11 Sega
- Remote Battery
- Coin Cell Battery
- NVRAM
2.12 Spooky Pinball
2.13 Stern
2.13.1 MPU-100/MPU-200
- Remote Battery
- Memory Capacitor
- Coin Cell Battery
- NVRAM
2.13.2 Whitestar
- Remote Battery
- Coin Cell Battery
- NVRAM
2.13.3 SAM
- Remote Battery
- Coin Cell Battery
- NVRAM
2.13.4 SPIKE
2.14 Williams
2.14.1 System 3-7
- Remote Battery
- Memory Capacitor
- Coin Cell Battery
- NVRAM
2.14.2 System 9
- Remote Battery
- Memory Capacitor
- Coin Cell Battery
- NVRAM
2.14.3 System 11/11A/11B/11C
- Remote Battery
- Memory Capacitor
- Coin Cell Battery
- NVRAM
2.14.4 WPC
- Remote Battery
- Remote Battery on WPC-95
- Coin Cell Battery
- NVRAM
Note: Games that utilize a real-time clock will need a battery instead of NVRAM to keep proper time. Otherwise, the date/time will not advance while the game is powered off.
2.14.4.1 Games Affected By a Real-Time Clock
WPC (Fliptronics II)
- Creature from the Black Lagoon (different music plays based on the day of the week)
- Twilight Zone (clock on the playfield shows correct time)
WPC-S
- Dirty Harry (midnight madness)
- Johnny Mnemonic (midnight madness)
- WHO dunnit (midnight madness)
- Theatre of Magic ("hermaphrodite position" - midnight madness does not depend on real time clock since it is a game mode)
WPC-95
- Congo (midnight madness)
- Junk Yard (midnight madness)
- NBA Fastbreak (midnight madness)
- Medieval Madness (midnight madness, but special mode needs to be enabled to activate it)