Gottlieb System 80

Note: This page is a work in progress. Please help get it to a completed state by adding any useful information to it.

1 Introduction

Put system info here

2 Games

2.1 System 80 1st Generation

• Spiderman January 1980
• Panthera May 1980
• Circus June 1980
• Counterforce August 1980
• Star Race October 1980

2.2 System 80 2nd Generation

• James Bond October 1980
• Time Line November 1980
• Force II January 1981
• Pink Panther March 1981
• Mars God of War April 1981
• Volcano July 1981
• Black Hole October 1981
• Haunted House February 1982

2.3 System 80a

• Devil's Dare August 1982
• Caveman September 1982
• Rocky September 1982
• Spirit November 1982
• Punk! December 1982
• Striker January 1983
• Krull February 1983
• Goin Nuts February 1983
• Qbert's Quest March 1983
• Super Orbit May 1983
• Royal Flush Dlx June 1983
• Amazon Hunt September 1983
• Rack 'Em Up November 1983
• Ready Aim Fire November 1983
• Jacks to Open May 1984
• Alien Star August 1984
• The Games August 1984
• Touchdown February 1985
• El Dorado March 1985
• Ice Fever May 1985

2.4 System 80b

• Chicago Cubs Triple Play July 1985
• Bounty Hunter September 1985
• Tag Team October 1985
• Rock January 1986
• Rock Encore May 1986
• Raven June 1986
• Hollywood Heat September 1986
• Genesis September 1986
• Gold Wings October 1986
• Monte Carlo January 1987
• Spring Break April 1987
• Amazon Hunt II May 1987
• Arena June 1987
• Victory October 1987
• Diamond Lady December 1987
• TX Sector February 1988
• Amazon Hunt III March 1988
• Robo-War April 1988
• Excalibur August 1988
• Bad Girls October 1988
• Hot Shots February 1989
• Big House April 1989
• BoneBusters August 1989

3 Technical Info

Things like Data East's controller board was a copy of William's System 11 with some changes would go here.

4 Problems and Fixes

4.1 Power Driver Issues

This may not apply to some, as MPU might have been part of it.

4.2 MPU Issues

4.2.1 Using An Old Computer Power Supply For Bench Testing

A MPU board is much easier to work on if it is removed from the backbox and placed on the test bench. An old computer power supply can be used to power the MPU board for testing on the bench.

Obtain and old computer power supply from an old computer. If you don't have an old computer setting around head on off to the thrift store and pick one up. Remove the power supply from the case by unscrewing the appropriate screws. Careful not to unscrew the power supply case itself.

Power Supply

Cut off one of the connectors from the power supply and clearly mark on the power supply box the value of each of the colored wires from the power supply. The Yellow wire is 12V, the red 5V and the black is ground. Strip off part of each of the wires. To put the MPU on the test bench you will only need one of the ground wires and the 5v (red) line. To hook up the power supply I have alligator clips that I connect to the 5v and ground line and to the corresponding J1 connection. I use larger alligator clips to make the connection.

J1 Connector

Mark the MPU board where the positive and negative (common) connection is for the five volts from the computer power supply. This is marked on connector J1. The image shows the A1J1 connector with the markings. I took the picture with the board still mounted in the machine. Connect the 5v supply with alligator clips to the positive connector on J1 and the black wire (ground) to the negative connector of J1. That's it, your good to go! --Kencaine 02:30, 24 April 2011 (BST)

4.4 Display Driver Board

Possibly doesn't apply to some, can't think of an example.

5 Game Specific Problems and Fixes

Example would be servo controller on Independence Day pinball

6 Repair Logs

Did you do a repair? Log it here as a possible solution for others.

6.1 Game Displays 000000 On Power Up and It's Not The Slam Switch

If you power the game on and all of the displays immediately display all zeros without strobing the problem is usually with the slam switch. However, if the slam switch modification has been done or the slam switch is working properly there is a problem with the switch matrix.

I had this problem on my Haunted House machine. I finally found that chip Z15 (7432) was bad.

I was fixing a kicker solenoid on the playfield, the playfield was still in the machine and fully in the upright position. While I was soldering the wire to the new solenoid I did not adequately protect the components below from a solder drip. Well I did have a solder drip that landed right on a pop bumper driver board connector and shorted the connector. The short caused more than just this problem but for this narrative we will restrict to the slam/switch matrix problem.

Reading in other materials I recognized the problem as the slam switch issue. There was little written about the problem outside of the slam switch. I decided to check the matrix by doing a diode check on all of the diodes in the switch matrix. When I did this I found that many of the diodes were testing bad. These were being tested with the board removed from the machine.

Having replacement diodes in my parts drawer I decided that these must have gone bad during the short. I unsoldered a few of the diodes and remeasured after the diode was removed and found the correct values on my meter for the removed diodes, they were not bad. I then noticed that the bad diodes were all in the same row on the switch matrix. They all traced back to the Z15 chip. I replaced the Z15 7432 and the problem was resolved. --Kencaine 01:43, 24 April 2011 (BST)