Difference between revisions of "Twilight Zone Eddy Boards"
(Created page with "The trough opto is one of the worst problems in the game, second only to the clock. It has a number of problems. Connector Spring Failure The trough eddy board and its sensor a...") |
|||
| Line 1: | Line 1: | ||
The trough opto is one of the worst problems in the game, second only to the clock. It has a number of problems. | The trough opto is one of the worst problems in the game, second only to the clock. It has a number of problems. | ||
| − | Connector Spring Failure | + | '''Connector Spring Failure''' |
The trough eddy board and its sensor are joined by a small cable. With the vibration from the trough, the pins lose spring and the connection becomes unreliable. There are two solutions. You can solder the wires directly to the boards. Or you can buy or make a new cable. | The trough eddy board and its sensor are joined by a small cable. With the vibration from the trough, the pins lose spring and the connection becomes unreliable. There are two solutions. You can solder the wires directly to the boards. Or you can buy or make a new cable. | ||
| − | Damaged Sensor | + | '''Damaged Sensor''' |
The sensor is adjustable, and needs to be within 1/16 of the ball to work. If it is too close, the ball hits it and destroys the plastic. If it gets to the wire, the sensor will permanently fail. Although the sensor may look beaten up, the problem is still usually the cable. | The sensor is adjustable, and needs to be within 1/16 of the ball to work. If it is too close, the ball hits it and destroys the plastic. If it gets to the wire, the sensor will permanently fail. Although the sensor may look beaten up, the problem is still usually the cable. | ||
| − | + | ''' | |
| − | Out of Tune Circuit | + | Out of Tune Circuit''' |
The design doesn't accommodate allvariations of parts and conditions, and may end up being too robust and never respond to a close ball - or it may never start up. One fix to try for a stuck red light is to add some twists to the cable, | The design doesn't accommodate allvariations of parts and conditions, and may end up being too robust and never respond to a close ball - or it may never start up. One fix to try for a stuck red light is to add some twists to the cable, | ||
| + | ''' | ||
| + | Failed Opto Output''' | ||
| − | + | The output is an opto across the switch matrix. A short to the switch matrix can destroy the opto. Replace the opto if the LED works correctly but there is no switch signal. | |
| − | + | '''How does Twilight Zone keep track of where the powerball is?''' | |
| − | How does Twilight Zone keep track of where the powerball is? | ||
The powerball is a ceramic ball used in 'Twilight Zone' and the machine discovers it's location by using a combination of four different methods: | The powerball is a ceramic ball used in 'Twilight Zone' and the machine discovers it's location by using a combination of four different methods: | ||
| − | + | * 1. By using the eddy sensor in the under playfield tunnel between the piano, camera, powerfield exit and dead end that ends up in the slot. If a ball triggers the piano, camera or dead end switches and then the slot switch triggers *but* the eddy wasn't triggered in between, then we know the powerball must have gone through. | |
| − | + | * 2. By using the eddy sensor in the ball trough | |
| − | + | * 3. By failing to grab a ball successfully on the loop magnets. | |
| − | + | * 4. By counting the powerball as it goes in and out of containers, such as the lock and trough. So if the machine knows there's two balls in the trough and you drained the powerball during single ball play, it'll be out the trough again in 2 balls time. | |
Revision as of 23:44, 26 April 2011
The trough opto is one of the worst problems in the game, second only to the clock. It has a number of problems.
Connector Spring Failure
The trough eddy board and its sensor are joined by a small cable. With the vibration from the trough, the pins lose spring and the connection becomes unreliable. There are two solutions. You can solder the wires directly to the boards. Or you can buy or make a new cable.
Damaged Sensor
The sensor is adjustable, and needs to be within 1/16 of the ball to work. If it is too close, the ball hits it and destroys the plastic. If it gets to the wire, the sensor will permanently fail. Although the sensor may look beaten up, the problem is still usually the cable. Out of Tune Circuit
The design doesn't accommodate allvariations of parts and conditions, and may end up being too robust and never respond to a close ball - or it may never start up. One fix to try for a stuck red light is to add some twists to the cable, Failed Opto Output
The output is an opto across the switch matrix. A short to the switch matrix can destroy the opto. Replace the opto if the LED works correctly but there is no switch signal.
How does Twilight Zone keep track of where the powerball is?
The powerball is a ceramic ball used in 'Twilight Zone' and the machine discovers it's location by using a combination of four different methods:
- 1. By using the eddy sensor in the under playfield tunnel between the piano, camera, powerfield exit and dead end that ends up in the slot. If a ball triggers the piano, camera or dead end switches and then the slot switch triggers *but* the eddy wasn't triggered in between, then we know the powerball must have gone through.
- 2. By using the eddy sensor in the ball trough
- 3. By failing to grab a ball successfully on the loop magnets.
- 4. By counting the powerball as it goes in and out of containers, such as the lock and trough. So if the machine knows there's two balls in the trough and you drained the powerball during single ball play, it'll be out the trough again in 2 balls time.