Viza Manufacturing

Note: This page is a work in progress. Please help get it to a completed state by adding any useful information to it.

1 Introduction

Viza Manufacturing was a short-lived manufacturing company best known for its 1978 Viza War 2-player head-to-head cocktail table. Viza Manufacturing was contracted to build games by Allied Leisure.

2 Games

2.1 Fabulous 50's

Unfortunately, not much is known about this game.

2.2 War

This game is often referred to as "Viza War", rather than just "War".

It is a 2-player head-to-head cocktail pinball machine.

The playfield artwork is taken from a portion of Frank Frazetta's painting "The Berserker"

This game appears to include various game-specific parts as well as parts from other manufacturers:

• Pop bumper assemblies, outhole kicker assemblies, and roll-over button switches from Allied Leisure. (Note: Late versions of the playfield covered the hole for the outhole kicker and substituted a Wico/Brunswick linear coil assembly for the Allied Leisure outhole kicker assembly. This appeared to be because Viza ran out of allied leisure assemblies.)
• Coils from Wico.
• Flipper assemblies and shooter lane coil assemblies from Wico/Brunswick.
• Slingshot assemblies and saucer hole kicker assemblies from Brunswick

It is speculated that there were around 100-200 games manufactured.

This game went through a few playfield and cabinet variations during production.

Early games used an EM-style system and relays to operate the game, with small PCBs for the digital displays, and also used chimes for sound. Later games used just two boards--an MPU and power supply board, as well as digital displays and electronic sounds. Both games used digit LED segment displays. It is one of the first, if not the first example of LED digit segment displays being used instead of high-voltage glass segment displays. GamePlan Used LED digit segment displays in their first game, Sharpshooter, the following year.

Paperwork, manuals, and schematics have not surfaced for either variant of this game.

3 Technical Info

3.1 Boardset

3.1.2 Solid State Games

3.1.2.1 MPU

The MPU controls the game logic, switch inputs, sound, feature lamps, solenoids (including all 8 flippers), and scoring data.

Two interesting features that weren't seen again for at least a decade were computer-controlled flippers and indicator lights for fuses.

A good portion of the PCB is used by flipper controls. The 8 large tube-shaped resistors, 16 transistors, and a dozen ICs connected in some way to driving the transistors for the flippers. The flippers are controlled entirely by the MPU, so there are no end-of-stroke switches on the flipper assemblies. There is also a game feature where the opposite player's flippers can be disabled for a short period of time by hitting a specific target, which explains the need for some of the additional logic for controlling the flippers.

The MPU has four potentiometers installed on the board, which each control tone and volume.

• 

  MPU (Front)

• 

  MPU (Back)

• 

  MPU Factory Modification (Back)for 10-ball play

Some MPUs have a factory modification on the back of the board on the 7445 chip which enables 10-ball play. 10 balls per game extended the game time, but since there were only 5 LEDs to indicate the number of balls, this is sometimes misidentified as a game malfunction. The modification can be reversed by removing the jumper and reconnecting the cut traces, and it will re-enable 5-ball play.

3.1.2.2 Power Supply

The power supply is fairly straight-forward. It takes the voltages from the transformer, rectifies them, and filters them, before being supplied to the rest of the game.

One interesting feature that wasn't seen again for at least a decade was the indicator lights for fuses.

• 

  Power Supply (Front)

• 

  Power Supply (Back)

3.1.2.3 Regulator

LM323K 3A 5V regulator.

• 

  Regulator (Front)

• 

  Regulator (Back)

3.1.2.4 Score Display

The score display has 6 digits, but only four of those digits ever actually change. The ones and tens place digits are permanently set as zeros.

• 

  Score Display (Front)

• 

  Score Display (Back)

• 

  Factory Modification(Back)

3.2 Game Theory & Operation

3.2.1 Solid State Games

The solid state games were configured for 2-player head-to-head gameplay only, with player 1 (side 1) being on the side with the coin door, and player 2 (side 2) being on the opposite side.

3.2.2 EM Games

The EM games were configured for either 1-player or 2-player gameplay (selectable using a toggle switch near the coin door), and with player 1 (side 1) being on the side with the coin door, and player 2 (side 2) being on the opposite side.

4 Problems & Fixes

4.1 Volume & Sound Adjustments

Volume Adjustment

There are four potentiometers on the MPU of Viza War that are used to adjust sound.

One potentiometer is used to adjust the pitch/tone of the 1000 point scoring sound, and another is used for the 100 point scoring sound. A third is used for adjusting the volume of the point scoring sounds. Lastly, the fourth potentiometer is used to adjust the volume of the remaining noises and sound effects.

If any adjustments result in scratching sounds from the speaker, that usually means the potentiometers are dirty and may need to be replaced.

5 Restoration & Disassembly

5.1 Outhole Kicker Disassembly

Because this game uses plastic parts, it is necessary to be extra careful when disassembling assemblies, especially the outhole kicker assembly. Improper disassembly may result in this:

Broken base plate

Read through the following steps first before attempting disassembly.

1. Unscrew the 3 screws that hold the metal coil bracket to the plastic base plate. Do *NOT* attempt to remove the coil bracket from the base plate. Many base plates have likely been broken and shattered by people attempting this. Note that there is still the end of a screw poking up through the foot of the coil bracket. This is screwed in from the underside of the base plate.
2. Unscrew the four screws holding the base plate to the playfield.
3. Flip the base plate over, and unscrew the phillips screw holding the coil bracket to the plastic base plate.
4. Unscrew the two screws holding the switch to the base plate.
5. If it's necessary to remove the kicker arm, use needle nose pliers to remove the E-clips, and carefully push the small end of plastic pins out.
6. To re-assemble, simply perform all the disassembly steps in reverse order. However, note that the compression spring on the plunger needs to be oriented so the end of the spring is flush against the plastic link, or the plunger will bind up when it fires.

• 

  Outhole Kicker Assembly

• 

  Step 1, remove screws

• 

  Step 3, Remove Screw

• 

  Step 6, Compression Spring Position

6 Parts Substitutions & Replacements

6.1 Electronics

6.1.1 Chips

• 5408 chips can be replaced by 7408 chips, but it is recommended to use 7408 or 74F08 chips, not 74LS08 since the input and output voltage tolerances are too low on the LS variant of the chip.

8 Documentation

Paperwork, manuals, and schematics have not surfaced for either the early or later variant of this game.

Datasheets are available from a variety of sources for the active electronics components.