Gottlieb System 80

Note: This page is a work in progress. Please help get it to a completed state by adding any useful information to it.

1 Introduction

Gottlieb System 80 Board Set - 1st Generation

Gottlieb's second generation of solid state pinballs is System 80. Capabilities were increased in terms of controllable lamps, solenoids, gameplay, and sound. No longer tied to an EM-esque platform, Gottlieb started to introduce games with more unconventional asymmetric playfields. System 80 marked a foray into double and triple level playfields, speech, multiball; unfortunately, it also represented a step backwards in reliability, with battery corrosion, connectors, and bad grounding plaguing the design.

Once a system 80 game has been methodically gone through with board design grounding flaws and connectors corrected, they are just as reliable as any of their contemporaries.

Gottlieb System 80 Board Set - 2nd Generation

Gottlieb System 80A Board Set

Gottlieb System 80B Board Set - Early

Gottlieb System 80B Board Set - Typical

2 Games

2.1 System 80 1st Generation

Title	Date of Release	Production#	Model #	Sound	Notes
The Amazing Spiderman	05-1980	7625	653	Sound only - Media:Gtb_sys80_sound.JPG
Panthera	06-1980	5220	652	Sound Only - Media:Gtb_sys80_sound.JPG
Circus	06-1980	1700	654	Sound Only- Media:Gtb_sys80_sound.JPG	Ultra Widebody
Counterforce	06-1980	3870	656	Sound Only- Media:Gtb_sys80_sound.JPG
Star Race	08-1980	870	657	Sound Only- Media:Gtb_sys80_sound.JPG	Ultra Widebody

2.2 System 80 2nd Generation

Title	Date of Release	Production#	Model #	Sound	Notes
James Bond	10-1980	3625	658	Sound only - Media:Gtb_sys80_sound.JPG
Time Line	12-1980	3167	659	Sound Only - Media:Gtb_sys80_sound.JPG
Force II	12-1981	2000	661	Sound Only- Media:Gtb_sys80_sound.JPG
Pink Panther	03-1981	2840	664	Sound Only- Media:Gtb_sys80_sound.JPG
Mars God of War	03-1981	5240	666	Sound & Speech - Media:Gtb_sys80&a_s&s.JPG	First Gottlieb with speech, lane change, and multi-ball
Volcano	09-1981	3655	667	Sound & Speech - Media:Gtb_sys80&a_s&s.JPG
Black Hole	10-1981	8774	668	Sound & Speech - Media:Gtb_sys80&a_s&s.JPG	First Gottlieb with 2-Level playing area, Export games used sound only board
Haunted House	06-1982	6835	669	Sound Only - Media:Gtb_sys80&a_s&s.JPG	First game with 3-Level playing area, Sound only, but used sound & speech board
Eclipse	1982	193	671	Sound Only- Media:Gtb_sys80_sound.JPG	Production game and available as a kit for James Bond 007

2.3 System 80a

Title	Date of Release	Production#	Model #	Sound	Notes
Devil's Dare	08-1982	3832	670	Sound & Speech - Media:Gtb_sys80&a_s&s.JPG	Export games may have used the sound only board - someone please confirm
Caveman	09-1982	1800	PV810	Sound & Speech - Media:Gtb_sys80&a_s&s.JPG	Pinball / Video game hybrid
Rocky	09-1982	1504	672	Sound & Speech - Media:Gtb_sys80&a_s&s.JPG
Spirit	11-1982	1230	673	Sound & Speech - Media:Gtb_sys80&a_s&s.JPG	Sound only, but used sound & speech board
Punk!	12-1982	959	674	Sound & Speech - Media:Gtb_sys80&a_s&s.JPG	Sound only, but used sound & speech board
Striker	11-1982	910	675	Sound & Speech - Media:Gtb_sys80&a_s&s.JPG	Sound only, but used sound & speech board
Krull	02-1983	10	676	Unknown
Goin' Nuts	02-1983	10	682	Unknown
Q*bert's Quest	03-1983	884	677	Sound & Speech - Media:Gtb_sys80&a_s&s.JPG
Super Orbit	05-1983	2100	680	Sound Only - Media:Gtb_sys80&a_s&s.JPG	Sound only, but used a less populated sound & speech board
Royal Flush Deluxe	06-1983	2000	681	Sound Only- Media:Gtb_sys80&a_s&s.JPG	Sound only, but used a less populated sound & speech board
Amazon Hunt	09-1983	1515	684	Sound Only- Media:Gtb_sys80&a_s&s.JPG	Sound only, but used a less populated sound & speech board. Later production games used the sound only piggyback sound board
Rack 'Em Up!	11-1983	1762	685	Sound Only - Media:Gtb_sys80a&b_sound.JPG
Ready... Aim... Fire!	11-1983	390	686	Sound Only - Media:Gtb_sys80a&b_sound.JPG
Jacks to Open	05-1984	2350	687	Sound Only - Media:Gtb_sys80a&b_sound.JPG
Alien Star	06-1984	1065	689	Sound Only - Media:Gtb_sys80a&b_sound.JPG	689A Denotes a revision in the ROM code
The Games	08-1984	1768	691	Sound Only - Media:Gtb_sys80a&b_sound.JPG
Touchdown	10-1984	711	688	Sound Only - Media:Gtb_sys80a&b_sound.JPG
El Dorado City of Gold	09-1984	905	692	Sound Only - Media:Gtb_sys80a&b_sound.JPG
Ice Fever	02-1985	1585	695	Sound Only - Media:Gtb_sys80a&b_sound.JPG

2.4 System 80b

Title	Date of Release	Production#	Model #	Sound	Notes
Chicago Cubs Triple Play	05-1985	~1365	696	Sound Only - Media:Gtb_sys80a&b_sound.JPG
Bounty Hunter	07-1985	1220	694	Sound Only - Media:Gtb_sys80a&b_sound.JPG
Tag Team Pinball	09-1985	1220	698	Sound Only - Media:Gtb_sys80a&b_sound.JPG
Rock	10-1985	1875	697	Sound Only - Media:GTB Sys80B Sound.JPG
Raven	03-1986	3550	702	Sound Only - Media:GTB Sys80B Sound.JPG
Rock Encore	04-1986	245	704	Sound Only - Media:GTB Sys80B Sound.JPG	Production game using same playfield art as Rock, but mainly available as a conversion kit for Rock
Hollywood Heat	06-1986	3400	703	Sound Only - Media:GTB Sys80B Sound.JPG
Genesis	09-1986	3500	705	Sound Only - Media:GTB Sys80B Sound.JPG
Gold Wings	10-1986	3260	707	Sound Only - Media:GTB Sys80B Sound.JPG
Spring Break	04-1987	3550	706	Sound Only - Media:GTB Sys80B Sound.JPG
Monte Carlo	02-1987	4315	708	Sound Only - [[Media:GTB Sys80B Sound.JPG]
Arena	06-1987	3099	709	Sound Only - Media:GTB Sys80B Sound.JPG
Victory	10-1987	3315	710	Sound and speech - Media:Gtb sys80b MA886 sound.JPG
Diamond Lady	02-1988	2700	711	Unknown
TX Sector	03-1988	2336	712	Sound and speech - Media:Gtb sys80b MA886 sound.JPG
Robo-War	04-1988	2130	714	Unknown - - Media:Gtb sys80b MA886 sound.JPG
Excalibur	11-1988	1710	715	Unknown -- Media:Gtb sys80b MA886 sound.JPG
Bad Girls	11-1988	2500	717	Sound and speech - Media:Gtb sys80b MA886 sound.JPG
Big House	04-1989	1977	713	Sound and speech - Media:Gtb sys80b MA886 sound.JPG
Hot Shots	04-1989	2342	718	Sound and speech - Media:Gtb sys80b MA886 sound.JPG
Bone Busters Inc.	08-1989	2000	719	Sound and Speech - Media:Gtb sys80b MA886 sound.JPG	Used 3 sound boards

Game date of release, production numbers, and model number provided by the Internet Pinball Database - http://www.ipdb.org

3 Technical Info

3.1 System 80 / 80A / 80B Board Set

3.3 The Wiring Color Code

Unlike every other pinball manufacturer, which adopted a two-color wiring code system, Gottlieb used three colors. Most wiring in a Gottlieb game used a white base color, which is the wire's insulation color, and three "striped" traces on each wire. I state most cases, because there are some wires which only used two colors - the green insulated ground lines which have a single yellow trace, or only one color - the white ground wires used in System 80B games with no trace at all. Below is the Gottlieb color chart.

#	Color
0	Black
1	Brown
2	Red
3	Orange
4	Yellow
5	Green
6	Blue
7	Purple
8	Gray
9	White

Does the color chart look familiar? Well, if you have an electronics background, it should. The Gottlieb wire code system is the same as the resistor color coding system.

Here are some examples of the color coding system. The color wire code for switch strobe line 0 is 400. 400 would be a white insulated wire with a yellow trace and two black traces, or commonly referred to as a yellow-black-black wire. The ground lines in early System 80 games are code 54. 54 would be a green insulated wire with one yellow trace.

There is one word of caution, which should be pointed out. If the connections on A1J2 and A1J3 are being replaced, there are wire colors on these connections which are very similar. Although each wire is located on a different housing, please proceed with caution, as it can be difficult to see all three traces without spinning the wire around. The wires which come to mind are 344 and 677 on A1J2, and 433 and 766 on A1J3.

3.4 Connector Designations

All Gottlieb machines have a common naming convention for all of the connectors in the game. A specific connection uses two parts - a prefix and a suffix. The prefix is the board number or an inline wire junction, and the suffix is the connection on the board or a sequential wire junction number. When referencing a specific connector pin within a housing, a dash follows the connection number. For example, the connector pin for the slam switch signal on the CPU board is A1J5-10. The coin door connection used on Devil's Dare is A15P1 and A15J1 - the connector pin for switch return 7 on the coin door is A15J1-8.

The following boards are assigned the same numbers throughout the System 80 / 80A / 80B platforms.

• CPU Board - A1
• Power Supply - A2
• Driver Board - A3
• Sound Board - A6
• Pop Bumper Driver Boards - A8
• Reset Board - A24

There are several other board designations used, however, they change from game to game.

3.5 Switch Matrix

The Gottlieb System 80 / 80A / 80B switch matrix consists of a maximum of 64 switches. There are a total of 8 switch strobes and 8 switch returns. However, not every switch in the matrix is used on every System 80 game.

Just like the System 1 switch numbering system, the System 80 switch numbers have a similar naming convention. Except, the System 80 switch numbering system is the opposite of System 1. If you are accustomed to working on System 1 games, pay close attention. With Gottlieb System 80 switches the first number of the switch is its strobe number, while the second number is switch's return number. An example would be switch 54. Switch 54 is located on strobe 5 and return 4 of the switch matrix.

	Strobe 0 (A1J6-1 / A1J5-2)	Strobe 1 (A1J6-2 / A1J5-3)	Strobe 2 (A1J6-3 / A1J5-4)	Strobe 3 (A1J6-4 / A1J5-5)	Strobe 4 (A1J6-5 / A1J5-6)	Strobe 5 (A1J6-6 / A1J5-7)	Strobe 6 (A1J6-7)	Strobe 7 (A1J6-8 / A1J5-9)
Return 0 (A1J6-10)	00	10	20	30	40	50	60	70
Return 1 (A1J6-11)	01	11	21	31	41	51	61	71
Return 2 (A1J6-12)	02	12	22	32	42	52	62	72
Return 3 (A1J6-13)	03	13	26	33	43	53	63	73
Return 4 (A1J6-14)	04	14	24	34	44	54	64	74
Return 5 (A1J6-15)	05	15	25	35	45	55	65	75
Return 6 (A1J6-16 / A1J5-8)	06	16	26	36	46	56	66	76
Return 7 (A1J6-17 / A1J5-1)	07	17	27	37	47	57	67	77

3.5.1 The "Missing" Gottlieb System 80 Switches

With the Gottlieb System 80 series of games, there are some switch assignments that are designated the same throughout the System 80, 80A, and 80B platforms. These switches are typically not listed in the switch matrix portion of the manual. You have to review the cabinet schematics, and decipher what switches use what return and strobe. However, it appears that Gottlieb / Premier changed this section of the schematic starting with Excalibur or Bad Girls by no longer listing the strobes for these switches. So, below are the "missing" switch assignments for any Sys80B. All the info applies for Sys80 and Sys80A, except the two advance buttons, which weren't used prior to Sys80B.

06 - left advance button (Sys80B only)

07 - play / test switch

16 - right advance button (Sys80B only)

17 - left coin switch

27 - right coin switch

37 - center coin switch

47 - replay button

57* - plumb bob and ball roll tilts (these have the same switch assignment as the playfield tilt switch)

• Black Hole is one exception. The switch assigned for the tilt on Black Hole is 26.

Note: The coin door slam switch is not part of the switch matrix.

3.5.2 Setting up a Game for Free Play

Early Gottileb solid state pinball machines, prior to 1990, did not have a free play option available within the game settings. With this simple modification, a game can be set up for free play. First, identify the diode strip in the bottom of the cabinet. Once the diode strip is found, locate the credit button and coin switch strobe line wires. The wires will be located on the left of the diode strip - the non-banded side of the diodes. Below is a list of the wires.

Credit button wire - Green-Yellow-Yellow

Left coin switch wire - Green-Brown-Brown

Center coin switch wire - Green-Orange-Orange

Right coin switch wire - Green-Red-Red

Gottlieb System 80 Transformer Board

Solder a small lead wire from the credit button wire to any of the coin switch wires. Make certain that the diode, credit button wire, and coin switch wire are still soldered securely to the diode strip terminal when finished. If soldering is not an option, use a small alligator clip test lead. Now, when the credit button is pressed, a credit will be incremented and decremented. A game can be easily started without the need to open the coin door to trip the coin switches anymore.

Please note that this modification does not apply to Gottlieb System 80A and System 80B machines. System 80A and 80B machines use diode boards with edge connections, which are typically located on the cabinet wall near the left flipper cabinet switch. In my experience, jumpering the diodes on System 80A and 80B games do not give the intended free play results of jumpered System 80 diodes. I attribute this to the System 80A and 80B software reading the switch matrix differently.

3.6 Power Supply

3.6.1 System 80 / 80A Power Supply

System 80 / 80A Power Supply

The System 80 / 80A power supply is very similar to the System 1 power supply, where as the circuit board is secured to a large "hot plate" heat sink. This style power supply is used for all System 80 and 80A games from Spiderman to Ice Fever, and is the source of the following:

• +5 VDC logic power
• +8 VDC offset voltage needed for the displays
• +60 VDC for the 6 or 7 digit displays
• +42 VDC for the status display
• Ground from earth ground located on the transformer panel
  

Unlike the System 1 power supply, the +5 VDC logic power is no longer rectified and filtered on the power supply itself. This process is now handled by a bridge rectifier and a large filtering capacitor located on the transformer panel. The System 80 power still employs a crowbar circuit [1] for the logic power, which is very beneficial.

System 80 / 80A Power Supply - Showing the Large Heat Sink

Although these power supplies are fairly reliable, there are some drawbacks to the design. By incorporating a large heat sink for the PMD10K40 / 2N6059 TO-3 transistor on the board, a lot of heat is dissipated throughout the whole board. This in turn will limit the life expectancy of the other electronic components on the board. Equally, the heat sink must be removed in order to perform component level repairs to the board.

3.6.2 System 80 / 80A Sound & Speech Power Supply

A sound & speech board (S&S) is used starting with Mars God of War (MGOW). Because of the voltages needed to drive some of the components on the S&S board, this secondary power supply is added to the power train. The voltages generated from this board are:

• +12 VDC used for the analog inverters and voice synthesizer chip
• -12 VDC used for the analog inverters
• +30 VDC used for amplification

~~ need pic inserted J.P.

There are two different variations of this power supply. The first style is used only with MGOW, and is not a printed circuit board (PCB). The electronic components were screwed to a block of wood, which is located on the left wall of the lower cabinet. Conducting tests and repairs to this style power supply can be awkward and difficult.

System 80 / 80A Sound & Speech Power Supply

Starting with Volcano, the S&S power supply is now on a circuit board, which is located in the head of the game with the other circuit boards. Even though each style of S&S power supply uses different components for the generation of +12 VDC, the end result is the same. The S&S power supply was no longer used when Gottlieb went a step backwards, and installed the System 80A sounds only board with the piggyback board. This change occurred during the run of Amazon Hunt.

3.6.3 System 80B Power Supplies

Starting with Chicago Cubs, the Gottlieb power train went through a bit of a face lift. The System 80B platform uses two separate boards to supply power. This design change is mainly due to the single display board, which rectifies the high voltage on the board itself.

System 80B +5 VDC Power Supply

The small power supply with the finned heat sink is only used to generate +5 VDC for logic power. Although, removing the heat sink is not necessary to work on the board, this power supply has its own set of issues. First, it does not have a crow bar circuit. If the LM338K voltage regulator fails, and fails whereas the voltage increases drastically, it can destroy electronic components on the other circuit boards. Secondly, it's not as bad, but heat is still dissipated throughout the board. Third, the adjustable potentiometer (pot) on the power supply is prone to failure, due to dirt, dust, and contaminants. Finally, it is typical for the header pins on the input and output of the board to develop cracked solder joints. The two latter problems can easily be overcome, and will be addressed in the power problems [2] section below.

System 80B Auxiliary Power Supply

Starting with Rock, the second power supply is added, and is referred to as the auxiliary power supply. The primary functions of this board is used to power the sound board, and amplify the audio output. A breakdown of the voltages supplied by the auxiliary power supply are as follows:

• -12 VDC
• +12 VDC

3.7 CPU Board

Gottlieb System 80 CPU Board

The System 80 CPU board is a 6502 based microprocessor system. The 6502 microprocessor (the very same one used in the first Apple computer) executes the basic operating system contained in the masked ROMs at U2/U3. The game code "personality" augments the basic operating system PROM(s) and is also contained in masked ROMs (the OEM ROMs were masked) at positions PROM1 and (possibly) PROM2. "Scratchpad" memory is added via a 5101 256x4 bit CMOS memory at Z5. Control of peripheral devices (in this case lamps, solenoids, switches and sound) is accomplished via three 6532 RIOTs (RAM-I/O-Timer) at U4, U5, and U6. Each RIOT in turn controls it's own "subsystem" to drive these devices.

• Reset section

• Switch matrix

• Solenoids and Lamps

• Displays

There are four generations of the System 80 board. All of the CPU boards can be easily identified by their revision numbers notated just below the operator adjustable dip switches.

3.7.1 1st Generation CPU Board

System 80 CPU Board - 1st Generation

The first generation CPU is used in the first 5 System 80 games, and is marked with the following:

• ASSY PB03-D100-001
• DET PB03-D102-011
• REV B ASSY.

This board uses two masked PROM chips for the game code. The chips are typically labeled with the three digit game model number followed by /1 or /2, designating the game PROM position. An example of this naming convention is shown in the pic to the left. 652/1X and 652/2X are game PROM 1 and PROM 2 for Panthera. The "X" in this case designates a code revision. The masked ROMs at position U2 and U3 are not socketed on this board.
With some simple modifications, this board is upward compatible to use a single 2716 EPROM placed in the PROM 1 socket of the board. With the change of U2 and U3, this board can be used in System 80A games. The board could potentially be used in a System 80B game with many modifications, and the addition of a daughter board, however, it is not recommended.

3.7.2 2nd Generation CPU Board

++ need pic ++
The second generation CPU is used in some System 80 games, and is marked with the following:

• ASSY PB03-D100-??? - check boards for the suffix
• DETAIL PB03-D107-001

This board uses a single 2716 EPROM chip for the game code located at the PROM 1 socket position. The chips are typically labeled with the three digit game model number. Occasionally, the chip's game number label will be followed by /1, /2, /3, or even /4. In this case, the number following the slash is the code revision number. An example of this naming convention is 658 /2, which is a game PROM for James Bond - code revision 2. The masked ROMs at position U2 and U3 are not socketed on this board either.
With the change of U2 and U3, this board can be used in System 80A games. The board could potentially be used in a System 80B game with many modifications, and the addition of a daughter board, however, it again is not recommended. The second generation CPU is backward compatible, provided a doubled up, single game PROM is used at the PROM 1 position.

3.7.3 3rd Generation CPU Board

System 80 CPU Board - 3rd Generation

The third generation CPU is used in some System 80 games, and is marked with the following:

• ASSY PB03-D100-011
• DETAIL PB03-D107-003

This board is essentially the same as the second generation board, except an eyelet ground trace was placed just above Z33 on the board. This ground trace was never used. All information which applies to the second generation CPU board, applies to this board. The third generation CPU is backward compatible, provided the same is done it as the 2nd generation board.

3.7.4 4th Generation CPU Board (System 80A)

System 80A CPU Board

The fourth generation CPU is used in all System 80A games, and is marked with the following:

• D 20869

This board is the same as the third generation board, except the U2 and U3 masked ROM chips have different code, and are now socketed. The PROM 2 socket is no longer populated on the board. The fourth generation CPU is backward compatible, provided the System 80 ROM code is installed at U2 and U3. If used on a game with the 1st generation CPU, the game code must be doubled up on a 2716 EPROM, and installed at the PROM 1 position. This board is forward compatible with System 80B, provided all of the above outlined modifications are performed. Out of all the System 80 CPU boards, this is the most compatible with System 80B, due to using the same base circuit board.

3.7.5 5th Generation CPU Board (System 80B)

System 80B CPU Board

The fifth generation CPU is used in all System 80B games, and is marked with the following:

• D 20869

Even though,the base circuit board is identical to the fourth generation CPU board, it's being named the fifth generation board, due to all of the major changes. The U2 and U3 masked ROM and sockets have been replaced with a piggyback daughter board mounted in the U3 position. The daughter board uses a 2764 EPROM. Most of the related display segment and digit chips are no longer populated. This is due to the single display board handling these functions on its own board. The missing chips once used for the displays are Z19, Z21, Z22, Z23, Z24, and Z25. Equally, jumpers have been placed where Z19 and Z21 once resided. The fifth generation CPU is backward compatible, after the daughter board has been removed, and the missing display chips populated.

Any of the Gottlieb System 80 / 80A / 80B CPU boards are compatible cross platform. It's just matter of how much work must be done to modify each board.

3.8 Driver Board

The System 80 Driver Board

The System 80 Driver board is responsible for all controlled lamps, relays, and all solenoids in the game. The CPU controls the driver board operation via a simple interface between A1J4 on the CPU and A3J1 on the driver board. Although the driver board went through some minor changes over the years, the same board can be adapted for all of the System 80 platforms.

To control the games' total of 51 lamps, the interface provides "device select" signals for each of the 74175s (Quad-D Flip-Flops) on the driver board, and 4 "bits" of data that is loaded (or "clocked") into a particular 74175 via the aforementioned device selects. Each lamp is driven discretely by a particular output of a particular 74175, which in turn drives an MPS-A13 or MPS-U45 transistor, (NDS-U45 transistors were used in place of MPS-U45s in some cases). Gottlieb did not implement a "lamp matrix" as some other manufacturers did.

It is noteworthy that there are some dedicated lamp transistors, which control specific game relays across the System 80 / 80A platforms. Relays such as the game over, tilt, and coin lockout relays are controlled by Q1, Q2, and Q3 respectively. The tilt and game over relays use the same designation for the System 80B platform, however, the use of a coin lockout relay was abandoned by this time. One neat feature of the driver board circuitry is that lamp "n" is driven by transistor Q"n+1". i.e. L12 is driven by Q13.

To control the games' solenoids, the driver board uses signals directly from the CPU to enable transistors on the driver board which turn on up to 9 solenoids. For solenoid control, the driver board uses MPS-U45, 2N3055, and 2N6043 transistors. Starting and ending with the System 80 platform, (games from Spiderman to Haunted House), three transistors were reserved to drive optional mechanical coin counters. These mechanical coin counter solenoids and associated transistors are: solenoid 3 (Q54), 4 (Q55), and 7 (Q56). Starting with the System 80A platform, (Devil's Dare), these transistors were no longer reserved for coin counters, and were used for other functions.

The games' sound signals (S1, S2, S4, S8) also pass through the driver board at Z14, a 7404 Hex Inverter. See below for S16 and S32.

Repurposed Driver Board Circuits:

A Typical Remote Transistor Mounted Under the Playfield

Since quite a few System 80 games employ more than 9 solenoids, and since the original driver board design will drive a maximum of 9 solenoids, Gottlieb repurposed some lamp outputs to drive "under-playfield transistors" which drive additional solenoids.

A Typical Transistor Driver Board

Once playfields became littered with numerous "under-playfield transistors", Gottlieb opted to merge some of these transistors into a transistor driver board. The transistor driver board started to appear on Gottlieb games nearly midway through the System 80B platform, with the game Victory.

The sound S16 and S32 signals are also repurposed lamp outputs. For instance, Haunted House and Black Hole both repurpose L9 to S16. Robo-War repurposes lamp 4 to S16. Note that S16 is not consistently implemented across the System 80 family. Note also that references to the usage of S32 are difficult to find.

3.11 Displays

3.11.1 System 80 - 6 Digit Displays

3.11.2 System 80A - 7 Digit Displays

3.12 Bookkeeping & Diagnostics

Gottlieb System 80 Coin Door Test Button Highlighted

To enter the bookkeeping/diagnostic mode, open the coin door and press the micro switch. (Note this switch has no credit function) The credit display will now show "00", then press the start switch and the CPU will enter its diagnostic mode (or press the self test switch again for bookkeeping.) Pressing the self test switch will advance it to the next test.

Bookkeeping (System80 only!)
1 Coins thru left chute
2 Coins thru right chute
3 Coins thru center chute
4 Total plays
5 Total replays
6 Game percentage
7 Extra ball
8 Total tilts
9 Total slams
10 Times HGTD has been beaten
11 First high score level
12 Second high score level
13 Third high score level
14 High game to date score
15 Average playing time

Diagnostics
16 Lamp output test
17 Coil output test (will cycle and display #)
18 Switch test. (99 = no fault) You can also check switch numbers by pressing them on the playfield now.
19 Display test. Displays will cycle through numbers
20 Memory test. (99 = no fault)

You can trigger the slam switch, tilt switch or wait 60 seconds to reset the CPU back to play mode. (This is why my slam switch is still functional!)

4 Problems and Solutions

4.2 Power Problems

Bridges, orange cap in cabinet

4.3 MPU boot issues

4.3.1 Relocating the battery from the MPU board

The first thing you should do to any System 80 MPU is remove the rechargeable NiCad battery from the MPU board. All batteries leak. It's simply a matter of when they will leak. A leaking battery will damaged your (sometimes irreplaceable) board.

There are at least four methods of relocating and/or replacing the battery on your System 80 MPU.

• You can remove the battery completely and not replace it. The 5101 memory will not persist from power-up to power-up and therefore, high scores, replay levels, and credits will be lost.

Remote Battery

• You can mount a remote battery pack that uses standard AA batteries (x3) to protect your board. You must also incorporate a blocking diode (1N4001, although a 1N4004 will work just as well) to prevent the game from attempting to charge the batteries. Install the blocking diode in series with the positive lead of the battery pack, with the band oriented toward the MPU.

Here a 5.5V, 1F Super Cap is used to retain 5101 memory for up to 30 days

• You can replace the battery with a 1F 5.5V "SuperCap". The capacitor will never leak, will charge during power-on cycles, and will retain 5101 memory for about 30 days.

• You may remotely mount a replacement NiCad battery in a location that, should it leak, damage to valuable circuit boards will not occur.
  

4.3.2 Repairing Alkaline Corrosion

A System 80 MPU with alkaline damage repaired/cleaned. Reset circuitry replaced with the much simpler Dallas Maxim 1811

If you find that the battery has leaked, alkaline damage can be cleaned up, traces repaired, and new components installed with kits available from several sources, including Great Plains Electronics.

An alternative to replacing a great many of the components is to use the Dallis/Maxim DS1811 reset generator. The DS1811-10 has a typical trip point of 4.35VDC. You may also use the Microchip Technology equivalent, part number MCP130-450DI/TO, available from Great Plains Electronics.

4.3.3 Slam Switch Modification

In order to test the CPU board on the test bench, a modification must be made to the CPU board to make the CPU think that the slam switch is closed. If the CPU thinks that the slam switch is not closed, the CPU will not complete the boot process, instead booting into a mode where the displays flicker all zeros at a very rapid rate.

Gottlieb designed the slam switch as a normally closed switch. That is, the switch must be closed for the machine to operate normally. When a brute kicks the machine, the slam switch will open from the inertial force on the weight attached to the switch, and the slam switch will open. Since the CPU is on the bench, we need a way to have this switch closed at all times to properly test the board.

Additionally, slam switches themselves fail. It's a good idea to implement this change as a preemptive fix for slam switch failures.

Slam Switch Mod

The slam switch can effectively be permanently closed by making a small solder bridge across two traces to the right of Z26 (which is on the lower right side of the CPU board). To permanently close the switch, remove the solder mask by scraping with a sharp knife or screwdriver. Create the solder bridge between the two now bare traces. This change will connect pin 13 of Z26 to ground, permanently closing the switch.

Alternative Slam Switch Mod

An alternate method of achieving the same results is to solder a clipped resistor leg across the bottom of capacitor (C30) and resistor (R20), both immediately to the left of Z26.

Keep in mind that the last 4 Gottlieb System 80B games were released with normally open slam switches. Do not perform the slam switch modification on these games. This includes the following games:

• Bad Girls
• Big House
• Hot Shots
• Bonebusters, Inc.
  

4.3.4 Connecting a logic probe to the MPU

A great place to source power for your logic probe while diagnosing the board is across the filter capacitor just to the right of connector J1. Connect the black lead of your logic probe to the negative (bottom) lead of the capacitor. Connect the red lead of your logic probe to the positive (top) lead of the capacitor. Take care to ensure that the clips don't short to adjacent components.

4.3.5 Using a PC Power Supply For Bench Testing

Future Update****This section works for now, but we can generalize bench power supply construction here: Building a flexible power supply for bench testing PCBs

The MPU board is much easier to work on if it is removed from the backbox and placed on the test bench. An AT-style PC power supply can be used to power the MPU board on the bench.

Obtain an old PC power supply. If you don't have an old computer laying around, head on off to the thrift store and pick one up. Remove the power supply from the case by unscrewing the appropriate screws. Be careful not to unscrew the power supply case itself.

Power Supply

Clip one of the connectors from the power supply wire bundle and clearly mark on the power supply box the value of each of the colored wires from the power supply. Typically, the yellow wire is 12V, red is 5V, and the black is ground. Strip insulation from the end of the red wire and the black wire as the System 80 MPU requires only 5V and ground to boot. Use alligator clips to connect 5v and ground to the appropriate J1 connection. I use larger alligator clips to make the connection easier.

J1 Connector

Mark connector J1 where the positive and negative (common) connection is for the five volts from the computer power supply. The ground connection is on the top of the connector, the 5V connection is on the bottom. The image shows A1J1 with the markings. I took the picture with the board still mounted in the machine. Connect the 5v supply with alligator clips to the positive connector on J1 and the black wire (ground) to the negative connector of J1. That's it! you're good to go! --Kencaine 02:30, 24 April 2011 (BST)

4.12 Updating a dual game PROM MPU (1st generation) to a single game PROM configuration (2nd generation)

As noted earlier, the first five system 80 games used both sockets at PROM1 and PROM2, populating them with 8K byte masked ROMs. Should one of these ROMs fail, you may be able to find a replacement, but they are becoming more pricey, more difficult to find, and are still prone to failure as they age.

A more flexible solution would be to update the MPU to use a single 2716 UVEPROM at the PROM1 socket.

Modifications must be made to both the solder side and the component side of the board.

Component side modifications:

Solder side modifications:

Your MPU board is now configured for any System 80 (but not 80A or 80B) game. All that remains is to acquire a 2716 EPROM containing the game's code.

4.13 Using a 2732 game PROM in a System 80B MPU

Need a jumper from TC1 pin x to J3, IIRC...need to verify...Chris Hibler

5 Game Specific Problems and Fixes

5.1 Replacing the Black Hole "Spinning Disk" Motor

Here ya go Intrepid...have at it... :-)

Thanks, please be patient.....

6 Repair Logs

Did you do a repair? Log it here as a possible solution for others.

6.1 Game Displays 000000 On Power Up and It's Not The Slam Switch

If you power the game on and all of the displays immediately display all zeros without strobing the problem is usually with the slam switch. However, if the slam switch modification has been done or the slam switch is working properly there is a problem with the switch matrix.

I had this problem on my Haunted House machine. I finally found that chip Z15 (7432) was bad.

I was fixing a kicker solenoid on the playfield, the playfield was still in the machine and fully in the upright position. While I was soldering the wire to the new solenoid I did not adequately protect the components below from a solder drip. Well, I did have a solder drip that landed right on a pop bumper driver board connector and shorted the connector. The short caused more than just this problem but for this narrative we will restrict to the slam/switch matrix problem.

Reading in other materials I recognized the problem as the slam switch issue. I used a logic probe to test other components and found the CPU board working, mostly as it should except for acting like the machine was slam tilted. There was little written about the problem outside of the slam switch. I decided to check the matrix by doing a diode check on all of the diodes in the switch matrix. When I did this, I found that many of the diodes were testing bad. These were being tested with the board removed from the machine.

Having replacement diodes in my parts drawer I decided that these must have gone bad during the short. I began unsoldering a few of the diodes. Once disconnected from the circuit board I remeasured the removed diodes and found the correct values on my meter, they were not bad. I then noticed that the bad diodes were all in the same row on the switch matrix. They all traced back to the Z15 chip. I replaced the Z15 7432 and the problem was resolved. --Kencaine 01:43, 24 April 2011 (BST)