Bally 6803

Note: This page is a work in progress. Please help get it to a completed state by adding any useful information to it.

Click to go back to the Bally/Stern solid state repair guides index.

1 Introduction

Put system info here

Bally 6803 Board Set

2 Games

Game Title	Game Number	Sound	Displays	Keypad Used	Notes
Eight Ball Champ	0B38	Squawk & Talk	4 7-Digit / 1 6-Digit	Yes
Beat the Clock	0C70	Squawk & Talk	4 7-Digit / 1 6-Digit	Assumed Yes
Lady Luck	0E34	Cheap Squeak	4 7-Digit / 1 6-Digit	Assumed Yes
Motordome	0E14	T. C. S.	2 "Special" 14-Alphnumeric	Yes
Black Belt	0E52	T. C. S.	2 "Special" 14-Alphnumeric	Assumed Yes
Special Force	0E47	Sounds Deluxe	2 "Special" 14-Alphnumeric	Yes
Strange Science	0E35	T. C. S.	2 "Special" 14-Alphnumeric	Yes
City Slicker	0E79	T. C. S.	2 "Special" 14-Alphnumeric	Yes
Hardbody	0E94	T. C. S.	2 "Special" 14-Alphnumeric	Yes
Party Animal	0H01	Sounds Deluxe	2 "Special" 14-Alphnumeric	Assumed Yes
Heavy Metal Meltdown	0H03	Sounds Deluxe	2 "Special" 14-Alphnumeric	Yes
Dungeons & Dragons	0H06	Sounds Deluxe	2 "Special" 14-Alphnumeric	Yes
Escape from the Lost World	0H05	Sounds Deluxe	2 "Special" 14-Alphnumeric	No
Blackwater 100	0H07	Sounds Deluxe	2 "Special" 14-Alphnumeric	Assumed No
Truck Stop	2001	D-11581-2001	2 "Special" 14-Alphnumeric	No	Uses a sound interface board to process signals for sound board
Atlantis	2006	D-11581-2006	2 "Special" 14-Alphnumeric	No	Uses a sound interface board to process signals for sound board

Game model numbers provided by the Internet Pinball Database - http://www.ipdb.org

3 Technical Info

3.1 CPU Board

Bally 6803 CPU Board

3.1.1 CPU Board ROM Info and Jumper Settings

Game	U2	U3	Jumpers
Eight Ball Champ	Not Used	0B38-00803-0005	2, 4, 6, 8, 10
Beat the Clock*	Not Used	0C70-00803-0005	2, 4, 6, 9, 10
Lady Luck	Not Used	0E34-00803-0005	2, 4, 6, 8, 10
Motor Dome	E14A-42AAE-BX40	E14A-42AAE-CX4D	2, 4, 6, 8, 10
Black Belt	0E52-00803-0001	0E52-00803-0002	2, 4, 6, 8, 10
Special Force	0E47-00803-0004	0E47-00803-0005	2, 4, 6, 9, 10
Strange Science	0E35-00803-0001	0E35-00803-0002	2, 4, 6, 9, 10
City Slicker	0E79-00803-0002	0E79-00803-0003	2, 4, 6, 9, 10
Hard Body	E94A-12601-0000	E94A-12602-0000	2, 4, 6, 9, 10
Party Animal	H01A-12601-0000	H01A-12602-0000	2, 4, 6, 9, 10
Heavy Metal Meltdown	H03A-12601-0000	H03A-12602-0000	2, 4, 6, 9, 10
Dungeons & Dragons	H06A-12601-0000	H06A-12602-0000	2, 4, 6, 9, 10
Escape from the Lost World	H05A-12601-0000	H05A-12602-0000	2, 4, 6, 8, 10
Blackwater 100	H07A-12601-0000	H07A-12602-0000	2, 4, 6, 9, 10
Truck Stop	H08A-12601-0000	H08A-12602-0000	2, 4, 6, 9, 10
Atlantis	2006-12601-0000	2006-12602-0000	2, 4, 6, 9, 10

*Beat the Clock manual may state W8 in, W9 out. However, there was a service bulletin after the game was released stating the opposite.

3.2 Sound Boards

3.2.1 Squawk & Talk

Bally Squawk & Talk Sound Board

3.2.1.1 Cheap Squeak Sound Board

Bally Cheap Squeak Sound Board A080-91603-XXXX or Midway P/N M-051-00114-XXXX

The Cheap Squeak was designed as a lesser expensive sound board. It only utilizes a 6803 microprocessor, which allows it to function without 6821 PIAs and external RAM memory. This sound board is only capable of simple tones and sounds, but not speech. Although the Cheap Squeak is used in a handful of -35 based Bally games, Lady Luck is the only 6803 based game which uses it.

At power up, the Cheap Squeak's LED will flicker briefly, then flash, flash again, then turn on and stay on. Once the LED stays on, it seems to turn itself off for certain sounds, and then turn back on. Likewise, it appears to idle with the LED on, when no sounds are playing. The LED May turn on and off when sounds are playing or idle, but this is not always the case.

With Lady Luck, upon pressing the self test button (SW1), the sound board will play an explosion type noise. The board will then reboot itself.

Board Theory of Operations
The 6803 (U1) microprocessor multiplexes A0-A7 with D0-D7, calling those signals AD0-AD7. The processor fetches information from the sound ROMs (both code to execute and sound clips) by placing address information on AD0-AD7 and strobing the processor's AS (address strobe) signal to the 74LS373 (U2), thereby latching the lower 8 bits of the address bus in the LS373. A8-A15 are used along with jumpers JW1 through JW12, to implement a memory mapped I/O scheme to address the 2 sound ROMs which can be 2532s, 2732s, or 2764s. A14 and A15 control the 74LS10 (a triple 3-input nand gate) to assert device selects to the ROMs.

Note that the processor does not use the traditional R/W signal as it never "writes" to memory. Besides placing instruction address and data on the address and data busses, the processor reads sound selects via P20-P24 and writes sound data to the DAC via P10-P17. Think of these lines as PA1-PA7 of a 6821 or 6532.

The 6803 is initialized by the MPU at power up into 6803 mode N. Once initialized and running, the sound ROM code running in the 6803 accepts sound signal commands and merely reads pre-formatted sound "clips" from the sound ROMs and then writes the data to the ZN429 (U6) digital-to-analog converter (DAC) 8 bits at a time. The DAC converts the digital data to an analog level which is presented to the amplifiers for output to the speaker(s).

The board creates 5VDC on board by regulating 12VDC down to 5VDC. Unregulated 12VDC enters the board at J1-10. It is filtered by C8, C9, and C10. The inductor at L1 smooths the voltage somewhat. D6 (VR332, equivalent to a 1N5402), D7, and D8 drop the voltage by .5 - .7 volts (normal voltage drop across a diode). The 7805 at U9 further regulates the voltage down to 5VDC which can be measured at TP2 (TP3 is ground).

This 5VDC is used as a reference voltage by the amplifiers as well as to power the TTL logic ICs. The ZN429 DAC also uses this 5VDC as a voltage reference. To prevent the sound volume from fluctuating over the range of operating temperatures, the reference voltage is held constant by a "voltage divider biasing circuit" comprised of resistors at R22, R23, and R24, and a 2N5305 NPN transistor at Q7. This reference voltage is presented at pin 5 of the DAC.

Test Points

• TP1 should measure about 11VDC.
• TP2 is 5VDC.
• TP3 is ground.
• TP4 is the clock signal, provided externally by the 6803 for the purpose of synchronizing address and data read cycles.
• TP5 is the reset signal, which is also present on pin 6 of the 6803.
  

Bally Cheap Squeak Sound Board with Jumpers Highlighted

Jumpers JW2, JW4, JW7, JW10, and JW11 should be installed when U3 EPROM is installed for Lady Luck.

3.2.2 Turbo Cheap Squeak (T.C.S.)

The Bally Turbo Cheap Squeak (T.C.S.) Sound Board. Note that the headers, which are normally individual pins soldered directly to the board, have been replaced on this board. The test switch is also broken on this board.

The Turbo Cheap Squeak sound board was used on games like Strange Science and Motordome. The sounds it can produce are pretty basic.

The board features a 68B09EP processor, a 6821 PIA, 16K of static ram, and 256K of ROM. It interfaces to the MPU similarly to the Bally Squawk and Talk board. Volume is controlled by the pot at VR1.

Note that the board is marked "T.C.S. FOR PINBALL". Some Bally / Midway video games also use a Turbo Cheap Squeak sound board. The T.C.S. sound boards used for video games and pinball are not 1-to-1 compatible between one another.

The following games use the Cheap Squeak:

• Motordome
• Black Belt / Karate Kick
• Strange Science
• City Slicker
• Hardbody

Normal boot up diagnostics via the LED for the T.C.S is as follows:

• 1st Flash - Determines if the external ROM (U7) is good.
• 2nd Flash - Checks if the external RAM (U6) is good.
• 3rd Flash - Checks the 6821 PIA (U8).

3.2.3 Sounds Deluxe

Bally Sounds Deluxe Sound Board

3.3 Accessing Bookkeeping, Settings, and Diagnostics

6803 coin door test button

3.3.1 6803 Keypad

File:D&D keypad.jpg

The beloved 6803 keypad

As easy as "A, B, C".

4 Problems and Fixes

4.1 Power Driver Issues

This may not apply to some, as MPU might have been part of it.

4.2 MPU Issues

4.2.1 Relocating the Factory NiCad Battery off the MPU

Placeholder for System 80 CPU Board - 2nd Generation

The second generation CPU is used in some System 80 games, and is marked with the following:

• ASSY PB03-D100-??? - check boards for the suffix
• DETAIL PB03-D107-001

This board uses a single 2716 EPROM chip for the game code located at the PROM 1 socket position. The chips are typically labeled with the three digit game model number. Occasionally, the chip's game number label will be followed by /1, /2, /3, or even /4. In this case, the number following the slash is the code revision number. An example of this naming convention is 658 /2, which is a game PROM for James Bond - code revision 2. The masked ROMs at position U2 and U3 are not socketed on this board either.
With the change of U2 and U3, this board can be used in System 80A games. The board could potentially be used in a System 80B game with many modifications, and the addition of a daughter board, however, it again is not recommended. The second generation CPU is backward compatible, provided a doubled up, single game PROM is used at the PROM 1 position.

4.2.2 Leon's 6803 CPU Repair

http://www.pinwiki.com/wiki/index.php?title=Leon_Borre_Bally_6803_repair

4.4 Sound Issues

4.4.1 Sounds Deluxe Board

Bally Sounds Deluxe Sound Board

This sound board has a common problem with DAC failure. AD7533 chip is easy and inexpensive to replace. You can prevent failure by removing C12 (47 uf) capacitor. It seems to have no adverse affect but prevents a voltage condition on power down that can destroy the DAC.

The LED with flash a check sequence on power up. 6 Flashes ROMS and RAM are OK.

4.5 Display Driver Board

Possibly doesn't apply to some, can't think of an example.

4.6 Coins Register But Don't Credit Up

This is commonly seen on VPinMAME emulation, but applies to real life as well.

Coins drop OK, switch is good, game makes noise, but it remains on "Credits 0" and doesn't credit up.

Symptom is corrupted/blank NVRAM.

To fix, open coin door (make sure coin door switch is working, otherwise the keypad won't work), then do these steps:

Hit "Test", to enter operator mode.

Hit "A" until "Feature Options" is displayed.

Hit Enter.

It will say "Reset Factory Is".

Hit 6, then 5, then Enter.

Hit "Game" to return to attract mode. You'll know it worked because it will take longer than usual to reach attract mode, and the display will flicker slightly as the computer clears the memory (this is normal).

Intuitive and easy to remember, right? And Bally had the nerve to advertise "manual-free testing"....

5 Game Specific Problems and Fixes

Example would be servo controller on Independence Day pinball

6 Repair Logs

Did you do a repair? Log it here as a possible solution for others.